Nissan X-Trail 32. Instruction — part 1271
FAX-76
< REMOVAL AND INSTALLATION >
[4WD]
FRONT WHEEL HUB AND KNUCKLE
• When installing a cotter pin
and adjusting cap
, securely bend
the basal portion to prevent rattles.
CAUTION:
Never reuse cotter pin.
Disc rotor
CAUTION:
• Align the matching marks
made during removal when reus-
ing the disc rotor.
• Never drop disc rotor.
Strut Assembly and Steering Knuckle Connection
CAUTION:
Be sure to remove lubricants if lubricant has been used to separate the connection of strut assembly
and steering knuckle.
• Install the steering knuckle to strut assembly as follows.
1.
Set suitable jack under steering knuckle.
2.
Align the gap
of steering knuckle to the projection part
of
strut.
3.
Tighten the mounting bolt with pushing up the steering knuckle
until contacts stopper bracket
end face, using a suitable
jack.
CAUTION:
Check the stable condition when using a jack.
• Perform inspection after installation. Refer to
JPDIF0295ZZ
JPDIG0066ZZ
JMEIA0223ZZ
JMEIA0224ZZ
FRONT WHEEL HUB AND KNUCKLE
FAX-77
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
Inspection
INFOID:0000000010824409
INSPECTION AFTER REMOVAL
Check the following items, and replace the part if necessary.
• Check components for deformation, cracks, and other damage.
• Check boots of transverse link and steering outer socket ball joint for breakage, axial end play, and swing
torque.
- Transverse link: Refer to
.
- Steering outer socket: Refer to
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
BRC-212, "FRONT WHEEL SENSOR :
.
2.
Check the wheel alignment. Refer to
.
3.
Adjust neutral position of steering angle sensor. Refer to
.
FAX-78
< REMOVAL AND INSTALLATION >
[4WD]
FRONT DRIVE SHAFT BOOT
FRONT DRIVE SHAFT BOOT
MR20DD
MR20DD : Exploded View
INFOID:0000000010824410
LEFT SIDE
JSDIA5389ZZ
Circular clip
Dust shield
Housing
Snap ring
Spider assembly
Stopper ring
Boot band
Boot
Shaft
Damper band
Dinamic damper
Joint sub-assembly
Dust shield
: Wheel side
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)].
: Always replace after every disassembly.
FRONT DRIVE SHAFT BOOT
FAX-79
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
RIGHT SIDE
MR20DD : Removal and Installation
INFOID:0000000010824411
REMOVAL
Wheel Side
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Remove wheel sensor from steering knuckle. Refer to
BRC-212, "FRONT WHEEL SENSOR : Removal
JSDIA5460GB
Dust shield
Joint sub-assembly
Circular clip
Boot band
Boot
Shaft
Damper band
Dynamic damper
Stopper ring
Spider assembly
Snap ring
Housing
Dust shield
Support bearing
Retainer
Support bearing bracket
: Wheel side
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)].
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст