Nissan X-Trail 32. Instruction — part 1275
FAX-92
< REMOVAL AND INSTALLATION >
[4WD]
FRONT DRIVE SHAFT BOOT
• Assembly: Refer to
FAX-119, "QR25DE : Disassembly and Assembly"
QR25DE : Inspection
INFOID:0000000010824415
INSPECTION AFTER REMOVAL
Check the following items, and replace the part if necessary.
• Check components for deformation, cracks, and other damage.
• Check boots of transverse link and steering outer socket ball joint for breakage, axial end play, and swing
torque.
- Transverse link: Refer to
.
- Steering outer socket: Refer to
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
BRC-212, "FRONT WHEEL SENSOR :
.
2.
Check the wheel alignment. Refer to
.
3.
Adjust neutral position of steering angle sensor. Refer to
.
R9M
R9M : Exploded View
INFOID:0000000010827937
LEFT SIDE
JSDIA5389ZZ
Circular clip
Dust shield
Housing
Snap ring
Spider assembly
Stopper ring
Boot band
Boot
Shaft
Damper band
Dynamic damper
Joint sub-assembly
Dust shield
: Wheel side
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)]
: Always replace after every disassembly.
FRONT DRIVE SHAFT BOOT
FAX-93
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
RIGHT SIDE
R9M : Removal and Installation
INFOID:0000000010826888
REMOVAL
Wheel Side
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Remove wheel sensor from steering knuckle. Refer to
BRC-212, "FRONT WHEEL SENSOR : Removal
JSDIA6125GB
Dust shield
Joint sub-assembly
Circular clip
Boot band
Boot
Shaft
Stopper ring
Spider assembly
Snap ring
Housing
Dust shield
Support bearing
Retainer
Support bearing bracket
Heat insulator
: Wheel side
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)].
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
FAX-94
< REMOVAL AND INSTALLATION >
[4WD]
FRONT DRIVE SHAFT BOOT
3.
Remove lock plate
from strut assembly.
• LHD: Refer to
BR-24, "FRONT : Exploded View"
.
• RHD: Refer to
BR-88, "FRONT : Exploded View"
4.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work.
• LHD (1 PISTON TYPE): Refer to
BR-51, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• LHD (2 PISTON TYPE): Refer to
BR-56, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
• RHD (1 PISTON TYPE): Refer to
BR-111, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• RHD (2 PISTON TYPE): Refer to
BR-116, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor. Refer to
FAX-72, "Removal and Installation"
.
6.
Remove cotter pin, adjusting cap and then loosen wheel hub
lock nut, using a hub lock nut wrench (A) (SST: KV40104000).
7.
Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub and bearing assembly from drive
shaft.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive
shaft cannot be separated even after performing the above pro-
cedure.
8.
Remove wheel hub lock nut.
9.
Remove transverse link from steering knuckle and front suspension member. Refer to
10. Separate steering outer socket from steering knuckle. Refer to
ST-22, "Removal and Installation"
JSDIA3795ZZ
JSDIA2708ZZ
JPDIG0070ZZ
FRONT DRIVE SHAFT BOOT
FAX-95
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
11. Remove drive shaft from wheel hub and bearing assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle.
• Be careful not to overextend slide joint.
12. Remove boot bands, and then separate boot from joint sub-assembly.
13. Screw drive shaft puller (A) (commercial service tool) into joint
sub-assembly screw part to a length of 30 mm (1.18 in) or more.
Support drive shaft with one hand and pull out joint sub-assem-
bly from shaft.
CAUTION:
• Align sliding hammer and drive shaft and remove them by
pulling directory.
• If joint sub-assembly cannot be pulled out, try after
removing drive shaft from vehicle. Refer to
14. Remove circular clip
from shaft.
15. Remove boot from shaft.
Transaxle Side
Remove boot after removing drive shaft.
• Remove: Refer to
FAX-125, "R9M : Removal and Installation"
.
• Disassembly: Refer to
FAX-131, "R9M : Disassembly and Assembly"
INSTALLATION
Wheel Side
1.
Clean the old grease on joint sub-assembly with paper waste.
2.
Fill serration slot joint sub-assembly
with NISSAN genuine
grease or equivalent until the serration slot and ball groove
become full to the brim.
CAUTION:
After applying grease, use a shop cloth to wipe off old
grease that has oozed out.
JSDIA5562ZZ
JPDIF0258ZZ
JPDIF0007ZZ
JPDIF0008ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст