Nissan X-Trail 32. Instruction — part 813
P2138 APP SENSOR
EC-381
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P2138 APP SENSOR
DTC Description
INFOID:0000000010775275
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
- APP sensor 1 or 2 circuit is open or shorted.
- Sensor power supply 2 circuit is shorted.
• Accelerator pedal position sensor (APP sensor 1 or 2)
• Sensor power supply 2 circuit
FAIL-SAFE
DTC CONFIRMATION PROCEDURE
1.
CHECK DTC PRIORITY
If DTC P2138 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. Refer to
.
NO
>> GO TO 2.
2.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and let it idle for 1 second.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P2138
APP SENSOR
(Throttle/pedal position sensor/switch “D”/
“E” voltage correlation)
Rationally incorrect voltage is sent to ECM compared with the signals from
APP sensor 1 and APP sensor 2.
Engine operating condition in fail-safe mode
Fail safe mode
Vehicle behavior
Others
The ECM controls the electric throttle control actuator in regulating the throttle opening in order
for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal condition.
Therefore, the acceleration will be poor.
NOTE:
If accelerator pedal position sensor 1 and 2 malfunction at the same time conducts following con-
trol.
• ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed
opening (approx. 5 degrees) by the return spring.
EC-382
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
P2138 APP SENSOR
Diagnosis Procedure
INFOID:0000000010775276
1.
CHECK DTC PRIORITY
If DTC P2138 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. Refer to
NO
>> GO TO 2.
2.
CHECK APP SENSOR 1 POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect accelerator pedal position (APP) sensor harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between APP sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK APP SENSOR 1 POWER SUPPLY CIRCUIT
Check the voltage between APP sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace malfunctioning part.
4.
CHECK APP SENSOR 2 POWER SUPPLY-1
1.
Turn ignition switch OFF.
2.
Disconnect APP sensor harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between APP sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> GO TO 5.
5.
CHECK APP SENSOR 2 POWER SUPPLY-2
Check the voltage between APP sensor harness connector and ground.
APP sensor
Voltage
(Approx.)
Connector
+
−
Terminal
CVT models
E110
4
2
5 V
M/T models
E167
+
−
Voltage
(Approx.)
APP sensor
Connector
Terminal
CVT models
E110
4
Ground
5 V
M/T models
E167
APP sensor
Voltage
(Approx.)
Connector
+
−
Terminal
CVT models
E110
5
1
5 V
M/T models
E167
P2138 APP SENSOR
EC-383
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> GO TO 6.
6.
CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between APP sensor harness connector and ECM harness connector.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace malfunctioning part.
7.
CHECK SENSOR POWER SUPPLY 2 CIRCUIT
Perform
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace malfunctioning part.
8.
CHECK APP SENSOR 1 GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between APP sensor harness connector and ECM harness connector.
4.
Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace malfunctioning part.
9.
CHECK APP SENSOR 2 GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between APP sensor harness connector and ECM harness connector.
+
−
Voltage
(Approx.)
APP sensor
Connector
Terminal
CVT models
E110
5
Ground
5 V
M/T models
E167
+
−
Continuity
APP sensor
ECM
Connector
Terminal
Connector
Terminal
CVT models
E110
5
E16
118
Existed
M/T models
E167
+
−
Continuity
APP sensor
ECM
Connector
Terminal
Connector
Terminal
CVT models
E110
2
E16
127
Existed
M/T models
E167
EC-384
< DTC/CIRCUIT DIAGNOSIS >
[MR20DD]
P2138 APP SENSOR
4.
Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace malfunctioning part.
10.
CHECK ECM GROUND CIRCUIT
Check the continuity between ECM harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace malfunctioning part.
11.
CHECK APP SENSOR INPUT SIGNAL CIRCUIT
1.
Check the continuity between APP sensor harness connector and ECM harness connector.
2.
Also check harness for short to ground and to power.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Repair or replace malfunctioning part.
12.
CHECK APP SENSOR
Check the APP sensor. Refer to
EC-385, "Component Inspection"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace accelerator pedal assembly. Refer to
ACC-4, "Removal and Installation"
+
−
Continuity
APP sensor
ECM
Connector
Terminal
Connector
Terminal
CVT models
E110
1
E16
120
Existed
M/T models
E167
+
−
Continuity
ECM
Connector
Terminal
F7
11
Ground
Existed
F8
54
55
56
E16
123
125
128
+
−
Continuity
APP sensor
ECM
Connector
Terminal
Connector
Terminal
CVT models
E110
3
E16
126
Existed
6
119
M/T models
E167
3
126
6
119
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст