Nissan X-Trail 32. Instruction — part 1033
DRIVE BELT AUTO-TENSIONER
EM-29
< REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
REMOVAL AND INSTALLATION
DRIVE BELT AUTO-TENSIONER
Exploded View
INFOID:0000000010783685
Removal and Installation
INFOID:0000000010783686
Removal
1.
Remove drive belt. Refer to
EM-22, "Removal and Installation"
.
• Keep each auto-tensioner pulley arm locked after drive belts are removed.
2.
Support the bottom surface of engine using a transmission jack, and then remove the rear torque rod and
the engine mounting insulator (RH). Refer to
.
CAUTION:
When using the jack, apply a piece of wood to the oil pan (lower) mounting bolt to protect the bot-
tom of engine from being scratched.
3.
Remove drive belt auto-tensioner mounting bolt
from service
hole
of right side member
.
NOTE:
Lift the front side of engine with a jack supporting the bottom of
engine and align drive belt auto-tensioner mounting bolt position
with the service hole.
4.
Remove drive belt auto-tensioner.
Installation
Install in the reverse order of removal.
CAUTION:
When installing drive belt auto-tensioner, be careful not to interfere with water pump pulley.
Front cover
Drive belt auto-tensioner
: N·m (kg-m, ft-lb)
JPBIA4304GB
: Drive belt auto-tensioner
: Vehicle front
PBIC3138J
EM-30
< REMOVAL AND INSTALLATION >
[MR20DD]
AIR CLEANER AND AIR DUCT
AIR CLEANER AND AIR DUCT
Exploded View
INFOID:0000000010783687
Air duct assembly
Mounting rubber
Bracket
Bracket
Air duct 1
Resonator duct
Resonator
Grommet
Collar
Air duct 2
Air cleaner cover
Air cleaner filter
Mounting rubber
Bracket
Air cleaner body
Mass air flow sensor
Clamp
PCV hose
To electric throttle control actuator
To rocker cover
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
JPBIA6796GB
AIR CLEANER AND AIR DUCT
EM-31
< REMOVAL AND INSTALLATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Removal and Installation
INFOID:0000000010783688
REMOVAL
NOTE:
Mass air flow sensor is removable under the car-mounted condition.
1.
Remove air duct 1 and air duct 2.
• To remove air duct 2
, pinch pawl
to unlock, move pawl
frontward, and remove air duct 2
upward.
2.
Remove battery. Refer to
PG-140, "EXCEPT FOR R9M : Exploded View"
3.
Remove battery tray. Refer to
PG-146, "EXCEPT FOR R9M : Exploded View"
.
4.
Disconnect mass air flow sensor harness connector.
5.
Loosen clamps of air duct assembly.
• Add mating marks if necessary for easier installation.
6.
Remove air cleaner assembly (cover and body).
7.
Remove mass air flow sensor from air cleaner body, if necessary.
CAUTION:
Handle the mass air flow sensor with following cares.
• Never shock the mass air flow sensor.
• Never disassemble the mass air flow sensor.
• Never touch the sensor of the mass air flow sensor.
8.
Disconnect PCV hose.
9.
Remove air duct assembly.
10. Remove bracket, if necessary.
INSTALLATION
Note the following, and install in the reverse order of removal.
Air cleaner body
CAUTION:
Check that mounting rubber is positioned in the mounting location and be careful not to allow it to be
dislocated when installing air cleaner body.
Air duct assembly
• To install air duct assembly
, align the matching marks
on both
ends with the others.
CAUTION:
Never allow foreign materials (i.e. lint) to adhere to the mount-
ing part of air duct assembly and each mating part.
• Install hose clamps and tighten to the torque specified below.
Air duct 1
: Vehicle front
JSBIA4626ZZ
: Air cleaner body
: Electric throttle control actuator
: Vehicle front
: 4.5 Nm (0.46 kg-m, 40 in-lb)
JPBIA6831ZZ
EM-32
< REMOVAL AND INSTALLATION >
[MR20DD]
AIR CLEANER AND AIR DUCT
To install air duct 1
, hold resonator duct
by hand (see
) and
securely engage the joint.
Inspection
INFOID:0000000010783689
INSPECTION AFTER REMOVAL
Inspect air duct assembly for crack or tear.
• If anything found, replace air duct assembly.
: Vehicle front
JSBIA4596ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст