Nissan X-Trail 32. Instruction — part 1563
MA-42
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE (QR25DE)
• Insert the projection
of air cleaner element
in such a way so
that it becomes the position (upper front side of car) of illustration.
• Verify that there is no looseness in air cleaner cover and has been fixed accurately.
• Check that pawls
and
(3 in total) of air duct 2
are engaged.
AIR CLEANER FILTER : Inspection (Dry Paper Type)
INFOID:0000000011009181
INSPECTION AFTER REMOVAL
Examine with eyes that there is no stain, clogging, or damage on air cleaner element.
• Remove dusts (such as dead leafs) on air cleaner element surface and inside cleaner case.
• To clean air cleaner element
, blow air on it from the air intake manifold side
to remove trash or dust.
CAUTION:
• When blowing air on the air cleaner element, attach the
cover to the air cleaner case and stay away from the vehicle
as much as possible to prevent the entry of dirt into the air
cleaner case.
• Never blow air from the ambient air side to prevent clogging.
When the ambient air side needs to be cleaned, attach the
cover to the intake manifold side and lightly dust by hand.
• If clogging or damage is observed, replace the air cleaner element.
MAINTENANCE INTERVAL
MA-42, "AIR CLEANER FILTER : Inspection (Dry Paper Type)"
.
ENGINE OIL
ENGINE OIL : Draining
INFOID:0000000011009185
WARNING:
• Be careful not to get burned, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1.
Warm up the engine, and check for engine oil leakage from engine components. Refer to
: Projection
JPBIA6830ZZ
: Vehicle front
JPBIA6828ZZ
Ambient air side
Air blow direction
JSBIA3460ZZ
ENGINE MAINTENANCE (QR25DE)
MA-43
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
2.
Stop the engine and wait for 10 minutes.
3.
Loosen oil filler cap.
4.
Remove drain plug
and then drain engine oil.
ENGINE OIL : Refilling
INFOID:0000000011009186
1.
Install drain plug with new drain plug washer. Refer to
.
CAUTION:
Be sure to clean drain plug and install with new drain plug washer.
2.
Refill with new engine oil.
Engine oil specification and viscosity: Refer to
MA-23, "Fluids and Lubricants"
CAUTION:
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in the engine.
3.
Warm up engine and check area around drain plug and oil filter for engine oil leakage.
4.
Stop engine and wait for 10 minutes.
5.
Check the engine oil level. Refer to
OIL FILTER
OIL FILTER : Removal and Installation
INFOID:0000000011009187
REMOVAL
1.
Remove splash guard (RH). Refer to
EXT-35, "FENDER PROTECTOR : Exploded View"
.
2.
Using oil filter wrench [SST: KV10115801] (A), remove oil filter.
CAUTION:
• Oil filter is provided with relief valve. Use genuine NISSAN
oil filter or equivalent.
• Be careful not to get burned when engine and engine oil
may be hot.
• When removing, prepare a shop cloth to absorb any
engine oil leakage or spillage.
• Completely wipe off any engine oil that adheres to engine
and vehicle.
INSTALLATION
1.
Remove foreign materials adhering to the oil filter installation surface.
: Vehicle front
JPBIA1676ZZ
Engine oil capacity
: Refer to
LU-32, "Periodical Maintenance Specification"
: Vehicle front
JSBIA3423ZZ
MA-44
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE (QR25DE)
2.
Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
3.
Screw oil filter instructionly until it touches the installation surface,
then tighten it by 2/3 turn
. Or tighten to specification.
OIL FILTER : Inspection
INFOID:0000000011009188
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
.
2.
Start the engine, and check that there is no leakage of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
SPARK PLUG
SPARK PLUG : Removal and Installation
INFOID:0000000011009183
REMOVAL
1.
Remove air duct assembly. Refer to
.
2.
Remove ignition coil.
3.
Remove spark plug with spark plug wrench (commercial service
tool).
CAUTION:
• Never drop or shock spark plug.
• Never disassemble ignition coil.
INSTALLAITON
Install in the reverse order of removal.
SPARK PLUG : Inspection
INFOID:0000000011009184
INSPECTION AFTER REMOVAL
SMA010
Oil filter:
: 18.0 N·m (1.8 kg-m, 13 ft-lb)
JPBIA0077ZZ
:
14 mm (0.55 in)
JPBIA0030ZZ
ENGINE MAINTENANCE (QR25DE)
MA-45
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
Use standard type spark plug for normal condition.
Visually check the electrode for dirt and wear and the insulator for burning.
CAUTION:
• Never drop or shock spark plug.
• Never use wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be
used.
• Checking and adjusting plug gap is not required between
change intervals.
EVAP VAPOR LINES
EVAP VAPOR LINES : Inspection
INFOID:0000000010735320
1.
Visually inspect EVAP vapor lines for improper attachment and for cracks, damage, loose connections,
chafing and deterioration.
2.
Inspect fuel tank filler cap vacuum relief valve for clogging, sticking, etc.
Refer to
Spark plug (standard)
: Refer to
Cleaner air pressure:
Less than 588 kPa (5.9 bar , 6 kg/
cm
2
, 85 psi)
Cleaning time:
Less than 20 seconds
SMA773C
JPBIA0031ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст