Nissan X-Trail 32. Instruction — part 665
4WD HIGH TEMP IS DISPLAYED ON INFORMATION DISPLAY
DLN-71
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4WD HIGH TEMP IS DISPLAYED ON INFORMATION DISPLAY
Description
INFOID:0000000010992021
While driving, 4WD warning (4WD High Temp. Stop vehicle) is displayed on information display (combination
meter).
• This symptom protects drivetrain parts when a heavy load is applied to the electric controlled coupling and
multiple disc clutch temperature increases. Also, optional distribution of torque sometimes becomes rigid
before 4WD warning (4WD High Temp. Stop vehicle) is displayed. Both cases are not malfunction. Refer to
.
• When this symptom occurs, stop vehicle and allow it to idle for some times. Displays will stop and system
will be restored.
DLN-72
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21C]
TIRE SIZE INCORRECT IS DISPLAYED ON INFORMATION DISPLAY
TIRE SIZE INCORRECT IS DISPLAYED ON INFORMATION DISPLAY
Description
INFOID:0000000010992022
While driving, 4WD warning (Tire Size Incorrect: See Owner’s Instruction) is displayed on information display
(combination meter).
Diagnosis Procedure
INFOID:0000000010992023
1.
CHECK TIRE
Check the following.
• Tire pressure
• Wear condition
• Front and rear tire size (There is no difference between front and rear tires.)
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts. And then, drive the vehicle at speed of 20 km/h (12 MPH)
or more for 5 seconds or more. Improper size information is initialized accordingly.
2.
CHECK INPUT SIGNAL OF TIRE DIAMETER
With CONSULT
1.
Start the engine.
2.
Drive at 20 km/h (12 MPH) or more for approximately 4 minutes continually.
3.
Check “DIS-TIRE MONI” of CONSULT “DATA MONITOR” for “ALL MODE AWD/4WD”.
Does the item on “DATA MONITOR” indicate “0 - 4 mm”?
YES
>> INSPECTION END
NO
>> GO TO 3.
3.
TERMINAL INSPECTION
Check 4WD control unit harness connector for disconnection.
Is the inspection result normal?
YES
>> Replace 4WD control unit. Refer to
DLN-76, "Removal and Installation"
NO
>> Repair or replace the error-detected parts.
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
DLN-73
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000010992024
Use the chart below to find the cause of the symptom. The numbers indicate the order of the inspection. If nec-
essary, repair or replace these parts.
Reference
(MR20DD)
(QR25DE)
—
,
,
SUSPECTED PARTS
(Possible cause)
TRANSFER
OI
L (Level
low)
TRANSFER OI
L
(W
rong)
TRANSFER
OI
L (L
ev
el
to
o h
ig
h
)
LIQUID GA
SKET
(Damaged)
O-R
ING
(W
orn
o
r
da
ma
ge
d)
OIL SEAL (W
orn or
damaged)
GEAR (W
orn
or
da
ma
ge
d)
BEARING (W
orn or damaged)
Symptom
Noise
1
2
3
3
3
Transfer oil leakage
3
1
2
2
2
DLN-74
< PERIODIC MAINTENANCE >
[TRANSFER: TY21C]
TRANSFER OIL
PERIODIC MAINTENANCE
TRANSFER OIL
MR20DD
MR20DD : Inspection
INFOID:0000000011001968
OIL LEAKAGE
Check transfer surrounding area (oil seal, drain plug, and filler plug etc.) for oil leakage.
OIL LEVEL
1.
Remove filler plug
and gasket. Then check that oil is filled up
from mounting hole for filler plug.
CAUTION:
Turn the ignition switch OFF while checking oil level.
• Oil level should be level with bottom of filler plug mounting
hole. Add transfer oil if necessary. Refer to
2.
Set a new gasket on filler plug and install it on transfer assem-
bly. Refer to
.
CAUTION:
Never reuse gasket.
MR20DD : Draining
INFOID:0000000011001969
1.
Run the vehicle to warm up the transfer unit sufficiently.
2.
Turn the ignition switch OFF.
3.
Remove drain plug
and gasket.
4.
Drain transfer oil.
5.
Before installing drain plug, set a new gasket. Install drain plug
to transfer assembly and tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
MR20DD : Refilling
INFOID:0000000011001970
1.
Remove filler plug
and gasket. Then fill with new transfer oil
until oil level reaches the specified level near filler plug mounting
hole.
2.
Leave the vehicle for 3 minutes, and check the oil level again.
3.
Before installing filler plug, set a new gasket. Install filler plug to
transfer assembly and tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
QR25DE
JSDIA5349ZZ
JSDIA5350ZZ
Recommended
oil and capacity
: Refer to
.
JSDIA5349ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст