Nissan X-Trail 32. Instruction — part 1099
PRECAUTIONS
EM-293
< PRECAUTION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
5.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
INSTRUCTION 2 (FOR VEHICLES PARKED BY IGNITION SWITCH OFF)
1.
Unlock the door with intelligent key or remote keyless entry.
NOTE:
At this moment, ACC power is supplied.
2.
Open the driver side door.
3.
Open the hood.
4.
Close the driver side door.
5.
Wait at least 3 minutes.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
6.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
R9M engine
: 4 minutes
V9X engine
: 4 minutes
EM-294
< PREPARATION >
[R9M]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000010784302
NISSAN tool number
(RENAULT tool No.)
Tool name
Description
—
(Mot. 1979)
Piston ring compressor
Installing piston assembly into cylinder bore
KV10111100
(
—
)
Seal cutter
Removing oil pan and front cover. etc
KV10112100
(
—
)
Angle wrench
Tightening bolts for bearing cap, cylinder
head, etc. in angle
KV10114400
(
—
)
Heated oxygen sensor wrench
Loosening or tightening air fuel ratio sensor
a: 22 mm (0.87 in)
—
(Mot. 1970)
TDC set pin
To lock engine at TDC
—
(Mot. 1969)
Camshaft timing tool
To lock camshaft when changing timing chain
NT046
NT014
JPBIA0397ZZ
JPBIA0629ZZ
JPBIA0628ZZ
PREPARATION
EM-295
< PREPARATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Commercial Service Tools
INFOID:0000000010784303
—
(Mot. 1770)
Crankshaft pulley locking tool
To lock crankshaft pulley
—
(Mot. 1772)
Compression gauge adapter
Connecting compression gauge and glow
plug hole
•
: G1/4
•
: M10
×
1.0
•
: 64 mm
•
:
φ
8.5 mm
—
(Mot. 1773)
Positioning tool
To position the gear and apply for the right
clearance (wear compensation gear)
—
(Mot. 1959)
TORX Socket
Removing and installing drive plate or fly-
wheel
Size: T55+
—
(Mot. 1972)
Piston cooler fitting tool
Installing oil jet (9.5 degree orientation)
—
(Mot. 1485-01)
Piston cooler removing tool
Removing oil jet
—
(Mot. 1431)
Flywheel locking tool
To lock flywheel
—
(Emb. 880)
Piston cooler fitting tool
Pin extractor tool
NISSAN tool number
(RENAULT tool No.)
Tool name
Description
JPBIA0630ZZ
JSBIA5512ZZ
JPBIA0625ZZ
E1BIA0349ZZ
JMAIA0431ZZ
EM-296
< PREPARATION >
[R9M]
PREPARATION
NISSAN tool number
(RENAULT tool No.)
Tool name
Description
KV113B0040
(Mot. 251-01)
Dial indicator stand set
Gauge stand used with KV113B0050 (Mot.
252-01)
KV113B0050
(Mot. 252-01)
Dial indicator stand set
Thrust plate for measuring the protrusion of
piston used with KV113B0040 (Mot. 251-01)
KV113B0090
(Mot. 1335)
Valve seal remover
Tool for removing valve oil seals
KV113B0180
(Mot. 1511-01)
Valve seal drift
Tool for installing valve oil seals
KV113B0200
(Mot. 1573)
Cylinder head stand
Cylinder head and cylinder head housing sup-
port
Tube presser
Pressing the tube of liquid gasket
Valve spring compressor
Disassembling valve mechanism
MBIB0360E
MBIB0361E
MBIB0370E
MBIB0378E
MBIB0380E
NT052
JPBIA0770ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст