Nissan X-Trail 32. Instruction — part 706
ELECTRIC CONTROLLED COUPLING
DLN-235
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• After installing stud bolt, the length of the protrusion from
electric controlled coupling must be as described below.
NOTE:
When replacing electric controlled coupling assembly, stud bolts
are not required to be installed.
12. Install propeller shaft. Refer to
DLN-214, "Removal and Installa-
13. Refill gear oil to the final drive. Refer to
.
14. Perform inspection and adjustment after installation. Refer to
DLN-235, "Inspection and Adjustment"
Inspection and Adjustment
INFOID:0000000011008619
INSPECTION AFTER INSTALLATION
Check oil level and final drive for oil leakage. Refer to
ADJUSTMENT AFTER INSTALLATION
When replaced electric controlled coupling, perform writing unit characteristics. Refer to
Length (L)
: 19.8 mm (0.780 in)
±
1.4 mm (0.055 in)
JSDIA5441ZZ
DLN-236
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
AIR BREATHER
AIR BREATHER
Exploded View
INFOID:0000000011008620
Removal and Installation
INFOID:0000000011008621
REMOVAL
Final Drive Side
1.
Remove hose clamp, and remove air breather hose from breather connector (metal) on rear final drive
assembly.
2.
Remove breather connector (resin) together with air breather hose from bracket.
3.
Remove hose clamp, and remove air breather hose from breather connector (resin).
4.
Remove trim clip and remove bracket.
5.
Remove breather connector (metal) from rear final drive assembly.
• When removing/installing breather connector (metal), remove rear final drive assembly from the vehicle.
Refer to
DLN-239, "Removal and Installation"
.
Electric Controlled Coupling Side
1.
Remove air breather hose assembly from breather connector (metal) on electric controlled coupling
assembly.
2.
Remove air breather hose assembly from hose connector.
NOTE:
Breather connector (resin)
Trim clip
Bracket
Hose clamp
Air breather hose
Breather connector (metal)
Breather connector (resin)
Air breather hose
Clip
Hose connector
Air breather hose assembly
Breather connector (metal)
Rear final drive assembly
: Always replace after every disassembly.
JSDIA5437ZZ
AIR BREATHER
DLN-237
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
The air breather hose assembly and the protective tube of elec-
trical wiring harness are integrated.
3.
Remove clip from suspension member.
4.
Remove breather connector (resin) together with air breather
hose and hose connector from bracket.
5.
Remove trim clip and remove bracket.
6.
Remove breather connector (metal) from electric controlled cou-
pling assembly.
• When removing/installing breather connector (metal), remove
electric controlled coupling assembly from rear final drive
assembly. Refer to
DLN-231, "Removal and Installation"
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• For non-reusable parts, refer to
.
• When installing air breather hose, make sure there are no pinched or restricted areas on air breather hose
caused by bending or winding.
Final Drive Side
• Set breather connector (metal)
to rear final drive assembly with
the paint mark
facing vehicle front.
• Observe the following instructions to install breather connector
(resin)
, air breather hose
, breather connector (metal)
, and
hose clamp
as shown in the figure.
CAUTION:
• Be careful with insert dimension of breather connector and
set position of hose clamp.
• Be careful with orientation of hose clamp tab.
• Set bracket with the stopper
facing vehicle inside.
Electric Controlled Coupling Side
JSDIA5247ZZ
: Vehicle front
JSDIA5212ZZ
Insert dimension of
breather connector
(resin/metal)
: 20 mm (0.79 in) from breather
connector end (air breather
hose side)
Set position of hose
clamp
: 5 mm (0.20 in) from breather
hose end
JSDIA5439ZZ
JSDIA5213ZZ
DLN-238
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R145]
AIR BREATHER
• Securely install breather connector (metal) to the electric controlled
coupling assembly with the tip of tube faced in the vehicle front
direction. In addition, insert air breather hose
to tube spool part
of breather connector (metal)
.
• Install breather connector (resin)
, air breather hose
, hose
connector
, and clip
based on hose paint mark
as shown in
the figure, complying with the directions below.
CAUTION:
• Be careful with insert dimension of breather connector
(resin) and hose connector, and set position of clip.
• Cut extra band of clip.
• Set bracket with the stopper
facing vehicle inside.
: Vehicle front
JSDIA5230ZZ
Insert dimension of
breather connector
(resin) and hose
connector
: 20 mm (0.79 in) from breather
connector end (air breather hose
side) and hose connector end (air
breather hose side)
Set position of clip
: 5 mm (0.20 in) from breather hose
end
JSDIA5231ZZ
JSDIA5213ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст