Nissan X-Trail 32. Instruction — part 1753
REAR DRIVE SHAFT
RAX-29
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage in boot.
• Be careful not to touch the inside of the boot with the tip of tool.
11. Secure large and small ends of boot with new boot bands as shown in the figure.
CAUTION:
Never reuse boot band.
a.
For one-touch clamp band
• Secure the large and small ends of boot with new boot bands
as shown in the figure.
b.
For low profile type band
i.
Put boot band in the groove on drive shaft boot. Then fit pawls
(
) into holes to temporary installation.
NOTE:
For the large diameter side, fit projection
and guide slit
at
first.
ii.
Pinch projection on the band with suitable pliers to tighten band.
iii.
Insert tip of band below end of the pawl.
c.
For omege type band
i.
Secure the boot bands using the boot band crimping tool (A)
(SST: KV40107300).
CAUTION:
Never reuse boot band.
NOTE:
PDIA1188J
SDIA3557E
SDIA3558E
JPDIF0012ZZ
RAX-30
< REMOVAL AND INSTALLATION >
[4WD]
REAR DRIVE SHAFT
Secure boot band so that dimension (M) meets the specification
as shown in the figure.
12. Secure housing and shaft, and then make sure that they are in the correct position when rotating boot.
Install them with new boot band when the mounting positions become incorrect.
Inspection
INFOID:0000000010828173
INSPECTION AFTER REMOVAL
• Move joint up/down, left/right, and in the axial direction. Check for motion that is not smooth and for signifi-
cant looseness.
• Check boot for cracks or other damage, and also for grease leak-
age.
• If a malfunction is found, disassemble drive shaft, and then replace
with new one.
INSPECTION AFTER DISASSEMBLY
Shaft
Check shaft for runout, cracks, or other damage. Replace if there are any abnormal condition.
Joint Sub-Assembly (Wheel Side)
Check the following:
• Joint sub-assembly for rough rotation and excessive axial looseness.
• The inside of the joint sub-assembly for entry of foreign material.
• Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly.
Replace joint sub-assembly if there are any non-standard conditions of components.
Housing and Spider assembly (Final Drive Side)
Replace housing and spider assembly if there is scratching or wear of housing roller contact surface or spider
roller contact surface.
NOTE:
Housing and spider assembly are used in a set.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
.
M
: 1.0 – 4.0 mm (0.039 – 0.157 in)
DSF0047D
SDIA1163J
SERVICE DATA AND SPECIFICATIONS (SDS)
RAX-31
< SERVICE DATA AND SPECIFICATIONS (SDS)
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000010828174
Drive Shaft
INFOID:0000000010828175
*: For measuring position. Refer to
RAX-24, "Disassembly and Assembly"
.
Axial end play
0.05 mm (0.002 in) or less
Item
Standard
Grease quantity
Wheel side
35 – 45 g (1.24 – 1.58 oz)
Final drive side
40 – 50 g (1.42 – 1.76 oz)
Boots installed length
*
Wheel side
90.2 – 92.2 mm (3.551 – 3.630 in)
Final drive side
151.55 – 153.55 mm (5.97 – 6.05 in)
RF-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
RF
A
B
RF
N
O
P
CONTENTS
ROOF
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing Battery Terminal . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
SUNROOF SYSTEM . . . . . . . . . . . . ...
SUNROOF SYSTEM : Component Description . ...
SUNROOF SYSTEM : Sunroof Switch . . . . .....
SUNROOF SYSTEM : Sunroof Motor Assembly ...
SUNROOF SYSTEM : Sunshade Motor Assembly
. ..
SYSTEM . . . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . ...
Circuit Diagram . . . . . . . . . . . . . ...
ECU DIAGNOSIS INFORMATION . . . ..
BCM (BODY CONTROL MODULE) . . . . ...
List of ECU Reference . . . . . . . . . . .
SUNROOF MOTOR ASSEMBLY . . . . . ...
Reference Value . . . . . . . . . . . . . .
SUNSHADE MOTOR ASSEMBLY . . . . .
Reference Value . . . . . . . . . . . . . .
WIRING DIAGRAM . . . . . . . . . ..
SUNROOF SYSTEM . . . . . . . . . . ..
Wiring Diagram . . . . . . . . . . . . . ...
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORKFLOW . .
Work Flow . . . . . . . . . . . . . . . .
SYSTEM INITIALIZATION . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
ANTI-PINCH INSPECTION . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
POWER SUPPLY AND GROUND CIRCUIT .
SUNROOF MOTOR ASSEMBLY . . . . . . . ..
SUNROOF MOTOR ASSEMBLY :
Diagnosis Procedure . . . . . . . . . . . ..
SUNSHADE MOTOR ASSEMBLY . . . . . . .
SUNSHADE MOTOR ASSEMBLY :
Diagnosis Procedure . . . . . . . . . . . ..
COMMUNICATION SIGNAL CIRCUIT . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
VEHICLE SPEED SIGNAL CIRCUIT . . . .
Component Function Check . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
SUNROOF SWITCH . . . . . . . . . . ..
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . . .
SYMPTOM DIAGNOSIS . . . . . . . ..
SUNROOF AND SUNSHADE DOES NOT OP-
ERATE PROPERLY . . . . . . . . . . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст