Nissan X-Trail 32. Instruction — part 2152
TM-566
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
U1117 LOST COMMUNICATION (ABS)
U1117 LOST COMMUNICATION (ABS)
DTC Description
INFOID:0000000010622789
DTC DETECTION LOGIC
POSSIBLE CAUSE
• ABS actuator and electric unit (control unit)
• Harness or connector (CAN communication line is open or shorted)
FAIL-SAFE
• Stop/start system prohibited
• Restart the engine during the stop/start system operation
• Turn OFF the electric oil pump relay
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Start the engine and wait for 5 seconds or more.
2.
Check the DTC.
Is “U1117” detected?
YES
>> Go to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010622790
For the diagnosis procedure, refer to
LAN-17, "Trouble Diagnosis Flow Chart"
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
U1117
LOST COMM (ABS)
(Lost Communication With ABS)
When the ignition switch is ON, TCM is unable to receive the CAN com-
munications signal from ABS actuator and electric unit (control unit) con-
tinuously for 2 seconds or more.
P062F EEPROM
TM-567
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P062F EEPROM
DTC Description
INFOID:0000000010622791
TCM compares the calculated value stored in the flash ROM with the value stored in TCM. If the calculated
value does not agree with the stored value, TCM judges this as a malfunction.
DTC DETECTION LOGIC
POSSIBLE CAUSE
• TCM (Flash ROM)
• Harness or connector [TCM power supply (back-up) circuit is open or shorted]
FAIL-SAFE
• Stop/start system prohibited
• Restart the engine during the stop/start system operation
• Turn OFF the electric oil pump relay
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1.
Start the engine.
2.
Check the DTC.
Is “P062F” detected?
YES
>> Go to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010622792
1.
REPLACE TCM
Replace the TCM. Refer to
TM-676, "Removal and Installation"
>> WORK END
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P062F
EEPROM
(Internal Control Module EEPROM Error)
Flash ROM error is detected when turning ON the ignition switch.
TM-568
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
P0705 TRANSMISSION RANGE SENSOR A
P0705 TRANSMISSION RANGE SENSOR A
DTC Description
INFOID:0000000010622793
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector (Short circuit between transmission range switch and TCM)
• Transmission range switch
FAIL-SAFE
• Shift position indicator on combination meter is not displayed
• Selector shock is large
• Start is slow
• Acceleration is slow
• Lock-up is not performed
• Stop/start system prohibited
• Restart the engine during the stop/start system operation
• Turn OFF the electric oil pump relay
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1.
Turn ignition switch ON.
2.
Shift the selector lever through entire positions from “P” to “D”. (Hold the selector lever at each position for
5 seconds or more.)
3.
Check the first trip DTC.
Is “P0705” detected?
YES
>> Go to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010622794
1.
CHECK TCM INPUT SIGNALS
With CONSULT
1.
Turn ignition switch ON.
2.
Select “Data Monitor” in “TRANSMISSION”.
3.
Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, and “P POSITION SW”.
4.
Shift the selector lever through entire positions from “P” to “D” and check ON/OFF of each monitor item.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0705
T/M RANGE SENSOR A
[Transmission Range Sensor A Circuit (PRNDL
Input)]
When all of the following conditions are satisfied and this state is main-
tained for 2 seconds:
• Two or more range signals simultaneously stay ON continuously
• TCM power supply voltage: More than 11 V
Monitor item
Condition
Condition
D POSITION SW
Selector lever: “D” position
On
Other than the above
Off
P0705 TRANSMISSION RANGE SENSOR A
TM-569
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Without CONSULT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Turn ignition switch ON.
4.
Shift the selector lever from “P” to “D” and check voltage between TCM harness connector terminals and
ground.
Is the inspection result normal?
YES >> INSPECTION
END
NO-1 [“D POSITION SW” is “ON” when selector is not in “D” position. (Or connector terminal 4 is at power
voltage.)]>>GO TO 2.
NO-2 [“N POSITION SW” is “ON” when selector is not in “N” position. (Or connector terminal 5 is at power
voltage.)]>>GO TO 4.
NO-3 [“R POSITION SW” is “ON” when selector is not in “R” position. (Or connector terminal 6 is at power
voltage.)]>>GO TO 6.
NO-4 [“P POSITION SW” is “ON” when selector is not in “P” position. (Or connector terminal 7 is at power
voltage.)]>>GO TO 8.
2.
CHECK D POSITION SW CIRCUIT (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between TCM harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
N POSITION SW
Selector lever: “N” position
On
Other than the above
Off
R POSITION SW
Selector lever: “R” position
On
Other than the above
Off
P POSITION SW
Selector lever: “P” position
On
Other than the above
Off
+
−
Condition
Voltage
TCM
Connector
Terminal
F119
4
Ground
Selector lever: “D” position
10 – 16 V
Other than the above
Approx. 0 V
5
Selector lever: “N” position
10 – 16 V
Other than the above
Approx. 0 V
6
Selector lever: “R” position
10 – 16 V
Other than the above
Approx. 0 V
7
Selector lever: “P” position
10 – 16 V
Other than the above
Approx. 0 V
Monitor item
Condition
Condition
TCM
Continuity
Connector
Terminal
F119
4
2
Not existed
5
6
7
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст