Nissan X-Trail 32. Instruction — part 1117
ENGINE ASSEMBLY
EM-365
< UNIT REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
UNIT REMOVAL AND INSTALLATION
ENGINE ASSEMBLY
Exploded View
INFOID:0000000010784353
M/T models
JPBIA6927GB
Upper torque rod
Mass damper
Engine mounting insulator (RH)
Engine mounting bracket (RH)
Rear torque rod bracket
Rear torque rod
Engine mounting insulator (LH)
Engine mounting frame support (LH)
Stud bolt
Engine mounting bracket (LH)
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
EM-366
< UNIT REMOVAL AND INSTALLATION >
[R9M]
ENGINE ASSEMBLY
CVT models
Removal and Installation
INFOID:0000000010784354
WARNING:
• Situate the vehicle on a flat and solid surface.
• Place chocks at front and back of rear wheels.
CAUTION:
• Always be careful to work safely, avoid forceful or uninstructed operations.
• Never start working until exhaust system and coolant are cool enough.
• If items or work required are not covered by the engine section, refer to the applicable sections.
• Always use the support point specified for lifting.
• Use either 2-pole lift type or separate type lift as best you can. If board-on type is used for unavoid-
able reasons, support at the rear axle jacking point with a transmission jack or similar tool before
starting work, in preparation for the backward shift of center of gravity.
• For supporting points for lifting and jacking point at rear axle, refer to
JPBIA6928GB
Upper torque rod
Mass damper
Engine mounting insulator (RH)
Engine mounting bracket (RH)
Rear torque rod bracket
Rear torque rod
Engine mounting insulator (LH)
: N·m (kg-m, ft-lb)
ENGINE ASSEMBLY
EM-367
< UNIT REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
NOTE:
When removing components such as hoses, tubes / lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
Outline
Remove the engine and the transaxle assembly from the vehicle downward. Separate the engine and the tran-
saxle.
Preparation
1.
Drain engine coolant from radiator. Refer to
CAUTION:
• Perform this step when the engine is cold.
• Never spill engine coolant on drive belt.
2.
Remove the following parts.
• Engine under cover: Refer to
EXT-39, "ENGINE UNDER COVER : Exploded View"
.
• Road wheels tire (RH and LH): Refer to
• Front fender protector (RH and LH): Refer to
EXT-35, "FENDER PROTECTOR : Exploded View"
.
• Cowl top cover and cowl top extension: Refer to
.
• Drive belt: Refer to
.
• Battery and battery tray: Refer to
(Battery) and
(Battery tray).
• Air inlet tubes and air inlet hoses: Refer to
• Air duct (inlet) and air duct/air cleaner case assembly: Refer to
.
• Radiator hose (upper and lower): Refer to
.
• Exhaust front tube: Refer to
.
Engine Room LH
1.
Remove ECM and bracket. Refer to
EC-1226, "Removal and Installation"
2.
Remove harness bracket from engine mounting insulator (LH).
3.
Disconnect all connections of engine harness around the engine mounting insulator (LH), and then tem-
porarily secure the engine harness into the engine side.
CAUTION:
Protect connectors using a resin bag against foreign materials during the operation.
4.
Disconnect fuel hoses from fuel pump. Refer to
5.
Disconnect heater hoses, and install plugs them to prevent engine coolant from draining.
6.
Disconnect shift cable/select cable from transaxle. Refer to
(CVT models).
7.
Remove ground cable from transaxle side.
8.
Disconnect vacuum hose from brake booster.
Engine Room RH
1.
Remove ground cable.
2.
Disconnect reservoir tank hose (lower).
3.
Remove alternator. Refer to
.
4.
Remove A/C compressor with piping connected from the engine. Temporarily secure it on the vehicle side
with a rope to avoid putting load on it. Refer to
(Except for RUSSIA).
Vehicle Underbody
1.
Disconnect water hoses (to thermoplunger). Refer to
2.
Remove front wheel sensor (LH and RH) for ABS from steering knuckle. Refer to
3.
Remove brake caliper assembly with piping connected from steering knuckle. Temporarily secure it on the
vehicle side with a rope to avoid load on it. Refer to the following table.
EM-368
< UNIT REMOVAL AND INSTALLATION >
[R9M]
ENGINE ASSEMBLY
4.
Remove rear torque rod.
• Loosen the mounting bolts as shown in the figure.
5.
Remove propeller shaft (4WD models). Refer to
.
6.
Remove drive shaft (LH and RH). Refer to
(2WD models) or
(4WD models).
7.
Remove stabilizer connecting rod mounting nut and cap at strut side (RH and LH). Refer to
8.
Disconnect steering shaft to steering gear assembly. Refer to
.
9.
Disconnect clutch pipe. Refer to
. (M/T models)
10. Remove front suspension member. Refer to
11. Preparation for the separation work of transaxle is as follows:
• Remove transaxle joint bolts which pierce at oil pan (upper) lower rear side.
Removal
1.
Use a instruction lift table caddy (commercial service tool) or equiv-
alently rigid tool such as a transmission jack. Securely support
bottom of the engine and the transaxle assembly.
CAUTION:
When using the jack, apply a piece of wood to the oil pan
(lower) mounting bolt to protect the bottom of engine from
being scratched.
2.
Remove upper torque rod bolt (RH).
Handle
Brake caliper assembly
Reference
LHD
1 piston type
BR-50, "BRAKE CALIPER ASSEMBLY (1 PISTON
TYPE) : Exploded View"
2 piston type
BR-55, "BRAKE CALIPER ASSEMBLY (2 PISTON
TYPE) : Exploded View"
RHD
1 piston type
BR-110, "BRAKE CALIPER ASSEMBLY (1 PISTON
TYPE) : Exploded View"
2 piston type
BR-115, "BRAKE CALIPER ASSEMBLY (2 PISTON
TYPE) : Exploded View"
: Vehicle front
JPBIA6935ZZ
PBIC1190E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст