Nissan X-Trail 32. Instruction — part 1566
MA-54
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE (R9M)
5.
Remove oil pan drain plug
using a square driver [8 mm (0.315
in)]. Drain engine oil.
ENGINE OIL : Refilling
INFOID:0000000010828041
1.
Install drain plug with new washer. Refer to
.
CAUTION:
Be sure to clean drain plug and install with new washer.
2.
Refill with new engine oil.
Engine oil specification and viscosity: Refer to
MA-23, "Fluids and Lubricants"
.
CAUTION:
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in the engine.
3.
Warm up engine and check area around drain plug and oil filter body for engine oil leakage.
4.
Stop engine and wait for 10 minutes.
5.
Check the engine oil level. Refer to
.
6.
Perform "Engine oil data reset". Refer to
.
OIL FILTER
OIL FILTER : Removal and Installation
INFOID:0000000010828043
REMOVAL
WARNING:
Be careful not to get burned when engine and engine oil may be hot.
CAUTION:
• When removing, prepare a shop cloth to absorb any engine oil leakage or spillage.
• Completely wipe off any engine oil that adheres to engine and vehicle.
1.
Remove engine under cover. Refer to
EXT-39, "ENGINE UNDER COVER : Exploded View"
2.
Loosen oil filter body
using a socket [27 mm (1.06 in)].
• Loosen oil filter body until orifice
of the oil filter body is
exposed, and then drain engine oil.
• Catch the engine oil drip, using a tray or waste.
CAUTION:
Completely wipe clean any engine oil remaining on oil fil-
ter body or vehicle.
: Vehicle front
E1BIA0601ZZ
Engine oil capacity
: Refer to
LU-46, "Periodical Maintenance Specification"
E1BIA0602ZZ
ENGINE MAINTENANCE (R9M)
MA-55
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
3.
Remove oil filter body
, and then remove oil filter
and O-ring
.
• Push the O-ring in the one direction by hand, and then pick a
pushed out-part with fingers to remove the O-ring.
CAUTION:
Never use wires or screwdrivers to prevent the oil filter
body from damage.
INSTALLATION
1.
Completely remove all foreign objects adhering to the inside of oil filter body or O-ring mounting area.
2.
Install oil filter
and O-ring
to oil filter body
.
CAUTION:
Be sure to use a new O-ring.
• Securely press the oil filter into the oil filter body.
• When installing an O-ring, apply engine oil all around the O-
ring.
3.
Install oil filter body assembly to oil cooler. Refer to
OIL FILTER : Inspection
INFOID:0000000010828044
INSPECTION AFTER INSTALLATION
1.
Check that the engine oil level. Refer to
2.
Start the engine, and check that there is no leak of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check that the engine oil level, and adjust the level. Refer to
: Oil cooler side
E1BIA0600ZZ
: Oil cooler side
E1BIA0600ZZ
MA-56
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
CHASSIS MAINTENANCE
EXHAUST SYSTEM
EXHAUST SYSTEM : Inspection
INFOID:0000000011009196
Check exhaust pipes, muffler, and mounting for improper attach-
ment, leakage, cracks, damage or deterioration.
• If anything is found, repair or replace damaged parts.
CVT FLUID (RE0F10D)
CVT FLUID (RE0F10D) : Inspection
INFOID:0000000010828065
FLUID LEAKAGE
• Check transaxle surrounding area (oil seal and plug etc.)for fluid
leakage.
• If anything is found, repair or replace damaged parts and adjust
CVT fluid level. Refer to
CVT FLUID (RE0F10G)
CVT FLUID (RE0F10G) : Inspection
INFOID:0000000010828066
FLUID LEAKAGE
• Check transaxle surrounding area (oil seal and plug etc.)for fluid
leakage.
• If anything is found, repair or replace damaged parts and adjust
CVT fluid level. Refer to
M/T OIL (RS6F94R)
M/T OIL (RS6F94R) : Inspection
INFOID:0000000011008837
OIL LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
OIL LEVEL
SMA211A
SMA146B
SMA146B
CHASSIS MAINTENANCE
MA-57
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1.
Check oil level from filler plug mounting hole as shown in the fig-
ure, after removing filler plug
and gasket from transaxle
assembly.
CAUTION:
Turn the ignition switch OFF while checking oil level.
2.
Set a gasket on filler plug and install it on transaxle assembly.
CAUTION:
Never reuse gasket.
3.
Tighten filler plug to the specified torque. Refer to
M/T OIL (RS6F94R) : Draining
INFOID:0000000011008838
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug
and gasket, then drain gear
oil.
3.
Set a gasket on drain plug and install it to transaxle assembly.
CAUTION:
Never reuse gasket.
4.
Tighten drain plug to the specified torque. Refer to
M/T OIL (RS6F94R) : Refilling
INFOID:0000000011008839
1.
Fill with new gear oil until oil level reaches the specified level
at filler plug mounting hole, after removing filler plug
and gas-
ket from transaxle assembly.
2.
After refilling gear oil, check the oil level. Refer to
3.
Set a gasket on filler plug, and install it to transaxle assembly.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque. Refer to
M/T OIL [RS6F52A (2WD)]
M/T OIL [RS6F52A (2WD)] : Inspection
INFOID:0000000011004115
OIL LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
OIL LEVEL
JSDIA5819ZZ
JSDIA5820ZZ
Recommended
oil and capacity
: Refer to
.
JSDIA6128ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст