Nissan X-Trail 32. Instruction — part 341
DAS
CAMERA AIMING ADJUSTMENT
DAS-105
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
Change the magnification of print to 250 mm (9.84 in)
×
250 mm (9.84 in) and print the target mark sample.
JSOIA0633ZZ
DAS-106
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
REAR VIEW CAMERA WASHER/AIR BLOWER FUNCTION INSPECTION
REAR VIEW CAMERA WASHER/AIR BLOWER FUNCTION INSPECTION
Inspection Procedure
INFOID:0000000010727922
1.
CHECK REAR CAMERA WASHER/AIR BLOWER FUNCTION
1.
Start the engine.
2.
Select the ACTIVE TEST item “AIR&WASH ACTIVE” of “AVM” with CONSULT.
NOTE:
Before function check, perform the following items:
• Fill with washer fluid.
• Perform ACTIVE TEST item “WASH ACTIVE” of “AVM” with CONSULT for 4 seconds.
3.
With operating the test item, check the operation.
Is it properly operated?
Washer fluid ejects 4 - 6 times. (Normal function)>>INSPECTION END.
Washer fluid ejects 7 times or more.>>Properly install or replace air tube.
Washer fluid ejects only once>> Properly install or replace air tube.
Washer fluid does not eject>>Properly install washer tube or replace washer tube and check valve.
DAS
ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR CON-
TROL UNIT
DAS-107
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR
CONTROL UNIT
Description
INFOID:0000000010931470
• Always perform the around view monitor control unit configuration after replacing the around view monitor
control unit.
• Always perform the around view monitor calibration after removing and installing or replacing the rear cam-
era.
• Always perform the rear camera calibration after removing and installing or replacing the rear camera.
• Always perform the rear camera calibration after replacing the around view monitor control unit.
• Always perform the around view monitor calibration after replacing the around view monitor control unit.
CAUTION:
The system does not operate normally unless the around view monitor and rear camera calibration are
performed. Always perform it.
Work Procedure
INFOID:0000000010931471
1.
AROUND VIEW MONITOR CONTROL UNIT CONFIGURATION
Perform the around view monitor control unit configuration with CONSULT. Refer to
TION (AROUND VIEW MONITOR CONTROL UNIT) : Work Procedure"
.
>> GO TO 2.
2.
AROUND VIEW MONITOR CONTROL UNIT CALIBRATION
Perform the around view monitor calibration with CONSULT. Refer to
IMAGE (AROUND VIEW MONITOR) : Work Procedure"
.
>> GO TO 3.
3.
REAR CAMERA CALIBRATION
Perform the rear camera calibration with CONSULT. Refer to
DAS-110, "Work Procedure (Preparation)"
.
>> GO TO 4.
4.
PERFORM SELF-DIAGNOSIS
Perform the self-diagnosis of around view monitor control unit with CONSULT (AVM). Check if any DTC is
detected.
Is any DTC detected?
YES
>> Perform the trouble diagnosis for the detected DTC. Refer to
NO
>> GO TO 5.
5.
LDW AND BSW SYSTEM ACTION TEST
1.
Perform the BSW and DAA system action test. Refer to
DAS-92, "BSW : Work Procedure"
(BSW) and
DAS-95, "DAA : Work Procedure"
(DAA).
2.
Check that the BSW and DAA system operates normally.
>> WORK END
DAS-108
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
Work Procedure
INFOID:0000000010931472
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “Before Replace ECU”, and save the current vehicle specification in CONSULT.
Is the vehicle specification saved normally?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
REPLACE AROUND VIEW MONITOR CONTROL UNIT
Replace around view monitor control unit. Refer to
AV-268, "Removal and Installation"
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Select “Configuration” or “After Replace ECU”, and write the vehicle specification saved in CONSULT to
around view monitor control unit.
>> GO TO 6.
4.
REPLACE AROUND VIEW MONITOR CONTROL UNIT
Replace around view monitor control unit. Refer to
AV-268, "Removal and Installation"
>> GO TO 5.
5.
WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Select “WRITE CONFIGURATION - Instruction selection” and write in the following list at a around view monitor
control unit depending on a vehicle specification.
>> GO TO 6.
6.
PERFORM SELF-DIAGNOSIS
CONSULT Self Diagnostic Result
Setting item
Detail
Items
Setting value
HANDLE
LHD
LHD models
RHD
RHD models
TRANSMISSION
A/T
CVT models
M/T
M/T models
LDW FUNCTION
WITHOUT
Without LDW
WITH
With LDW
4WD/2WD
2WD
2WD models
4WD
4WD models
DISPLAY
TYPE C
Without navigation system
TYPE G
With navigation system
SONAR
WITHOUT
Without sonar system
WITH
With sonar system
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст