Nissan X-Trail 32. Instruction — part 50
AV-192
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
DTC Description
INFOID:0000000010714853
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Camera image signal circuit between front camera and around view monitor control unit
FAIL-SAFE
Camera image is not displayed (Gray screen display)
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn the ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds.
4.
Perform “All DTC Reading” with CONSULT.
5.
Check if the “U111C” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “U111C” detected as the current malfunction?
YES
>> Refer to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010714854
1.
CHECK CONTINUITY FRONT CAMERA POWER SUPPLY AND GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit connector and front camera connector.
3.
Check continuity between around view monitor control unit harness connector and front camera harness
connector.
With BSW
Without BSW
4.
Check continuity between around view monitor control unit harness connector and ground.
With BSW
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
U111C
FRONT CAMERA IMAGE SIGNAL
(Front camera image signal)
Camera image signal circuit is open or shorted.
Around view monitor control
unit
Front camera
Continuity
Connector
Terminals
Connector
Terminals
M102
68
E165
2
Existed
70
1
Around view monitor control
unit
Front camera
Continuity
Connector
Terminals
Connector
Terminals
M24
38
E165
2
Existed
37
1
Around view monitor control
unit
Ground
Continuity
Connector
Terminal
M102
68
Not existed
AV
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
AV-193
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Without BSW
Is inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK VOLTAGE FRONT CAMERA POWER SUPPLY
1.
Connect around view monitor control unit connector and front camera connector.
2.
Turn ignition switch ON.
3.
Check voltage between around view monitor control unit harness connector and ground.
With BSW
Without BSW
Is inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-268, "Removal and Installation"
3.
CHECK CONTINUITY CAMERA IMAGE SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit connector and front camera connector.
3.
Check continuity between around view monitor control unit harness connector and front camera harness
connector.
With BSW
Without BSW
4.
Check continuity between around view monitor control unit harness connector and ground.
Around view monitor control
unit
Ground
Continuity
Connector
Terminal
M24
38
Not existed
Around view monitor control unit
Standard voltage
Reference voltage
(Approx.)
Connector
Terminal
(+)
(
−
)
Terminal
M102
68
70
5.0 - 9.0 V
6.0 V
Around view monitor control unit
Standard voltage
Reference voltage
(Approx.)
Connector
Terminal
(+)
(
−
)
Terminal
M24
38
37
5.0 - 9.0 V
6.0 V
Around view monitor control
unit
Front camera
Continuity
Connector
Terminals
Connector
Terminals
M102
71
E165
4
Existed
72
5
Around view monitor control
unit
Front camera
Continuity
Connector
Terminals
Connector
Terminals
M24
40
E165
4
Existed
39
5
AV-194
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
U111C FRONT CAMERA IMAGE SIGNAL CIRCUIT
With BSW
Without BSW
Is inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK CAMERA IMAGE SIGNAL
1.
Connect around view monitor control unit connector and front camera connector.
2.
Turn ignition switch ON.
3.
Check signal between around view monitor control unit harness connector terminals.
With BSW
Without BSW
Is inspection result normal?
YES
>> Replace around view monitor control unit. Refer to
AV-268, "Removal and Installation"
NO
>> Replace front camera. Refer to
AV-269, "Removal and Installation"
.
Around view monitor control
unit
Ground
Continuity
Connector
Terminals
M102
71
Not existed
72
Around view monitor control
unit
Ground
Continuity
Connector
Terminals
M24
40
Not existed
39
Around view monitor control unit
Reference value
Connector
Terminal
(+)
(
−
)
Terminal
M102
71
72
Around view monitor control unit
Reference value
Connector
Terminal
(+)
(
−
)
Terminal
M24
40
39
JSNIA0834GB
JSNIA0834GB
AV
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
AV-195
< DTC/CIRCUIT DIAGNOSIS >
[WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
DTC Description
INFOID:0000000010714855
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Camera image signal circuit between side camera LH and around view monitor control unit
FAIL-SAFE
Camera image is not displayed (Gray screen display)
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn the ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds.
4.
Perform “All DTC Reading” with CONSULT.
5.
Check if the “U111D” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “U111D” detected as the current malfunction?
YES
>> Refer to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010714856
1.
CHECK CONTINUITY SIDE CAMERA LH POWER SUPPLY AND GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect around view monitor control unit connector and door mirror (passenger side) connector.
3.
Check continuity between around view monitor control unit harness connector and door mirror (passenger
side) harness connector.
LHD models with BSW
LHD models without BSW
RHD models with BSW
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
U111D
SIDE CAMERA LH IMAGE SIG-
NAL
(Side camera left image signal)
Camera image signal circuit is open or shorted.
Around view monitor control
unit
Door mirror (driver side)
Continuity
Connector
Terminals
Connector
Terminals
M102
56
D3
7
Existed
58
8
Around view monitor control
unit
Door mirror (driver side)
Continuity
Connector
Terminals
Connector
Terminals
M24
29
D3
8
Existed
30
7
Around view monitor control
unit
Door mirror (passenger
side)
Continuity
Connector
Terminals
Connector
Terminals
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст