Nissan X-Trail 32. Instruction — part 1674
PCS-66
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
COMPONENT PARTS
Push-button Ignition Switch
INFOID:0000000010741733
Push-button ignition switch is pressed, and transmits the status sig-
nal to BCM and IPDM E/R.
IPDM E/R
IPDM E/R detects push-button ignition switch (push switch) status, and transmits push-button igni-
tion switch status signal (CAN) to BCM.
Refer to
PCS-5, "Component Parts Location"
for detailed installation location.
BCM
• BCM controls power distribution system.
• BCM judges ignition switch position by push-button ignition switch (push switch) and vehicle con-
dition
• BCM checks the ignition switch position internally.
Refer to
BCS-6, "BODY CONTROL SYSTEM : Component Parts Location"
for detailed installation
location.
Key switch (without Intelli-
gent Key system)
Key switch detects that ignition key is inserted into the ignition key cylinder, and then transmits the
signal to BCM.
Door request switch (with
Intelligent Key system)
Door request switch detects door lock/unlock operation and transmits door request switch signal to
BCM
Door switch
Detects door open/close condition.
No.
Component
Description
JMMIA1374ZZ
PCS
SYSTEM
PCS-67
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYSTEM
POWER DISTRIBUTION SYSTEM
POWER DISTRIBUTION SYSTEM : System Description
INFOID:0000000010741734
SYSTEM DIADRAM
SYSTEM DESCRIPTION
• POWER DISTRIBUTION SYSTEM is the system that BCM controls with the operation of push-button igni-
tion switch and performs the power distribution to each power circuit. This system is used instead of the
mechanical power supply changing mechanism with the operation of the conventional key cylinder.
• Push-button ignition switch can be operated when Intelligent Key is in the following condition.
- Intelligent Key is in the detection area of the inside key antenna.
- Intelligent Key backside is contacted to push-button ignition switch.
• Push-button ignition switch operation is input to BCM as a signal. BCM changes the ignition switch position
according to the status and operates the following relays to supply power to each power circuit.
- Ignition relay (IPDM E/R)
- Ignition relay [fuse block (J/B)]
- Accessory relay
- Blower relay
• The ignition switch position can be confirmed with the lighting of the ON indicator lamp in push-button igni-
tion switch.
IGNITION BATTERY SAVER SYSTEM
When all the following conditions are met for 10 minutes, the battery saver system will cut off the power supply
(ignition switch position ON
→
OFF) to prevent battery discharge.
• Ignition switch is in the ON position
• Turn signal lamp is not in operation
• Selector lever is in the P position (CVT models)
NOTE:
For one minute after thirty minutes have passed or three minutes after twenty-seven minutes are passed, the
following display is indicated on information display in combination meter and sounds buzzer in combination
meter.
Reset Condition of Ignition Battery Saver System
If any of the following conditions are met the battery saver system is released.
• Ignition switch is not in the ON position.
JMMIA1781GB
Combination meter
Time
Information display
Buzzer
Power turned off to save the battery
Pipi-Pipi
(two seconds)
For 1 minute after 10 minutes have passed
Power will turn off to save the battery
3 minutes after 7 minutes are passed
PCS-68
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
SYSTEM
• Turn signal lamp is operation.
• Selector lever is not in the P position.
NOTE:
The ignition battery saver system can be temporarily disabled, without using CONSULT, to prevent it from
functioning when performing trouble diagnosis. Refer to
.
IGNITION SWITCH POSITION CHANGE TABLE BY PUSH-BUTTON IGNITION SWITCH OPERA-
TION
PCS-68, "AUTO ACC FUNCTION : System Description"
AUTO ACC FUNCTION
AUTO ACC FUNCTION : System Description
INFOID:0000000010741735
SYSTEM DIAGRAM
MODELS WITH INTELLIGENT KEY SYSTEM
MODELS WITHOUT INTELLIGENT KEY SYSTEM
DESCRIPTION
In conventional vehicles, power is supplied to the accessories of the vehicle after the ignition switch is turned
to the ACC position.
The AUTO ACC function is a function that bypasses the ignition switch ACC position and automatically distrib-
utes the accessory power supply to each switch and unit by door unlock operation, etc. using the Intelligent
Key (models with Intelligent Key) or the remote controller key (models without Intelligent Key).
JMMIA1831GB
JMMIA1832GB
PCS
SYSTEM
PCS-69
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
OPERATION FLOW
Ignition Switch On Status
In this status the ignition switch is operated and turned ON.
Audio / Navigation Available Status
• In this status the audio, navigation, and each switch and unit that is activated by the accessory power source
can be operated.
• When 10 minutes pass after conditions are satisfied while and audio and navigation are not operated, audio
and navigation turn OFF.
• When audio or navigation is operated within 10 minutes after conditions are satisfied, operation time is
extended for 10 minutes. Audio and navigation can be operated for a maximum of 30 minutes after the sta-
tus is satisfied.
Audio / navigation use intention check status
This is a status for checking the intention of using audio and navigation again after audio and navigation are
stopped.
Audio / navigation unavailable status
In this status audio and navigation become unavailable, but the switches and units other than those for audio
or navigation that can operate by using the accessory power source are available until the accessory power
source turns OFF.
OFF status
In this status the AUTO ACC function stops and power to the accessories is not supplied.
JMMIA1784GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст