Nissan X-Trail 32. Instruction — part 1029
PREPARATION
EM-13
< PREPARATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
EM03470000
Piston ring compressor
Installing piston assembly into cylinder bore
KV11103000
Pulley puller
Removing crankshaft pulley
KV11105210
Stopper plate
Fixing drive plate and flywheel
KV10119600
Injector remover
Removing fuel injector
KV101197S0
Injector seal drift set
Installing fuel injector seal ring
Tool number
Tool name
Description
S-NT044
NT676
ZZA0009D
JPBIA3746ZZ
JPBIA3281ZZ
EM-14
< PREPARATION >
[MR20DD]
PREPARATION
Commercial Service Tools
INFOID:0000000010783667
Tool name
Description
Pilot bushing puller
Removing pilot converter
Spark plug wrench
Removing and installing spark plug
: 14 mm (0.55 in)
Pulley holder
Crankshaft pulley removing and installing
Valve seat cutter set
Finishing valve seat dimensions
Piston ring expander
Removing and installing piston ring
Valve guide drift
Removing and installing valve guide
S-NT045
JPBIA0399ZZ
ZZA1010D
S-NT048
S-NT030
PBIC4012E
PREPARATION
EM-15
< PREPARATION >
[MR20DD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Lubricant or/and Sealant
INFOID:0000000010783668
Valve guide reamer
Reaming valve guide inner hole
Reaming hole for oversize valve guide
Oxygen sensor thread cleaner
Reconditioning the exhaust system threads
before installing a new heated oxygen sensor
(Use with anti-seize lubricant shown below.)
a: 18 mm (0.71 in) dia. for zirconia heated
oxygen sensor
b: 12 mm (0.47 in) dia. for titania heated ox-
ygen sensor
Anti-seize lubricant (Permatex 133AR
or equivalent meeting MIL specifica-
tion MIL-A-907)
Lubricating oxygen sensor thread cleaning
tool when reconditioning exhaust system
threads
Instruction lift table caddy
Removing and installing engine
Tube presser
Pressing the tube of liquid gasket
Tool name
Description
PBIC4013E
AEM488
AEM489
ZZA1210D
S-NT052
Name
Description
Note
Three bond 1215
Cylinder block
Water drain plug
Three bond 1217H
• Oil pan (lower)
• Rocker cover
• Timing chain
• Oil pan (upper)
• Camshaft
• Cylinder block
—
Three bond 1386B
Cylinder block
Plug
EM-16
< BASIC INSPECTION >
[MR20DD]
CAMSHAFT VALVE CLEARANCE
BASIC INSPECTION
CAMSHAFT VALVE CLEARANCE
Inspection and Adjustment
INFOID:0000000010783669
INSPECTION
Perform inspection as follows after removal, installation or replacement of camshaft or valve-related parts, or if
there is unusual engine conditions regarding valve clearance.
1.
Remove rocker cover. Refer to
.
2.
Measure the valve clearance with the following procedure:
a.
Set No. 1 cylinder at TDC of its compression stroke.
• Rotate crankshaft pulley
clockwise and align TDC mark (no
paint)
to timing indicator
on front cover.
• At the same time, check that both intake and exhaust cam
noses of No. 1 cylinder face inside (
) as shown in the figure.
• If they do not face inside, rotate crankshaft pulley once more
(360 degrees) and align as shown in the figure.
b.
Using a feeler gauge, measure the clearance between valve
lifter and camshaft.
: White paint mark (Not use for service)
PBIC3960E
: Camshaft (INT)
: Camshaft (EXH)
: Engine front
JPBIA4347ZZ
Valve clearance
: Refer to
.
PBIC3192J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст