Nissan X-Trail 32. Instruction — part 1074
OIL PAN (LOWER)
EM-193
< REMOVAL AND INSTALLATION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
OIL PAN (LOWER)
Exploded View
INFOID:0000000010783796
JSBIA3334GB
O-ring
Oil pan (upper)
O-ring
Oil filter
Drain plug
Drain plug washer
Oil pan (lower)
Oil strainer
O-ring
Comply with the installation procedure
when tightening. Refer to
Oil pan side
EM-194
< REMOVAL AND INSTALLATION >
[QR25DE]
OIL PAN (LOWER)
Removal and Installation
INFOID:0000000010783797
REMOVAL
WARNING:
To avoid the danger of being scalded, never drain the engine oil when the engine is hot.
NOTE:
When removing oil pan (lower) only, take step 2 and 3.
1.
Remove under cover.
2.
Drain engine oil. Refer to
.
3.
Remove oil pan (lower) with the following procedure:
a.
Loosen mounting bolts in reverse order as shown in the figure.
b.
Insert seal cutter [SST:KV10111100] (A) between oil pan (upper)
and oil pan (lower).
CAUTION:
Be careful not to damage the mating surface.
INSTALLATION
CAUTION:
Do not reuse drain plug washer.
1.
Install oil pan (lower) with the following procedure:
a.
Use a scraper (A) to remove old liquid gasket from mating sur-
faces.
• Also remove old liquid gasket from mating surface of oil pan
(upper).
• Remove old liquid gasket from the bolt holes and threads.
CAUTION:
Never scratch or damage the mating surface when cleaning
off liquid gasket.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Should be lubricated with oil.
: Sealing point
: Engine front
JSBIA3335ZZ
JSBIA2555ZZ
JPBIA0053ZZ
OIL PAN (LOWER)
EM-195
< REMOVAL AND INSTALLATION >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
b.
Apply a continuous bead of liquid gasket
with a tube presser
(commercial service tool) as shown in the figure.
Use Genuine Liquid Gasket or equivalent.
CAUTION:
Attaching should be done within 5 minutes after liquid gas-
ket application.
c.
Tighten bolts in numerical order as shown in the figure.
2.
Install oil pan drain plug.
• Refer to the figure of components of former page for installation direction of washer. Refer to
.
CAUTION:
Do not reuse drain plug washer.
3.
Install in the reverse order of removal after this step.
NOTE:
Pour engine oil at least 30 minutes after oil pan is installed.
Inspection
INFOID:0000000010783798
INSPECTION AFTER INSTALLATION
1.
Check engine oil level and adjust engine oil. Refer to
.
2.
Start engine, and check there is no leaks of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check engine oil level again. Refer to
: Oil pan (lower)
: 7.5 - 9.5 mm (0.295 - 0.374 in)
:
φ
4.0 - 5.0 mm (0.157 - 0.197 in)
: Engine outside
JSBIA3336ZZ
: Engine front
JSBIA3335ZZ
EM-196
< REMOVAL AND INSTALLATION >
[QR25DE]
OIL SEAL
OIL SEAL
VALVE OIL SEAL
VALVE OIL SEAL : Removal and Installation
INFOID:0000000010783799
REMOVAL
1.
Remove camshafts. Refer to
.
2.
Remove valve lifters. Refer to
.
3.
Rotate crankshaft, and set piston whose valve oil seal is to be removed to TDC. This will prevent valve
from dropping into cylinder.
CAUTION:
When rotating crankshaft, be careful to avoid scarring front cover with timing chain.
4.
Remove valve collet.
• Compress valve spring with valve spring compressor [SST:
KV10116200] (A), attachment [SST: KV10115900] (C) and
adapter [SST: KV10109220] (B). Remove valve collet with a
magnet hand.
CAUTION:
• Be careful not to damage valve lifter holes.
• Install Tool (A) in the center of valve spring retainer to
press it.
5.
Remove valve spring retainer and valve spring (with valve spring seat).
CAUTION:
Never remove valve spring seat from valve spring.
6.
Remove valve oil seal with a valve oil seal puller [SST:
KV10107902] (A).
INSTALLATION
1.
Apply new engine oil to valve oil seal joint surface and seal lip.
JPBIA1365ZZ
: Valve spring retainer
JSBIA3390ZZ
ALBIA0863GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст