Nissan X-Trail 32. Instruction — part 559
RADIATOR CORE SUPPORT
DLK-577
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
Remove fixing clip
of engine room harness connector
.
6.
Remove fixing clips
of engine room harness
from radiator
core support upper
.
7.
Remove fixing clip
of engine room harness
from radiator
core support upper
.
8.
Remove crash zone sensor. Refer to
SR-31, "Removal and Installation"
.
9.
Remove hood lock support stay mounting bolts, and then move hood lock support stay to a location where
it does not inhibit work.
10. Remove radiator mounting bracket fixing clips. Refer to
.
11. Remove radiator core support upper mounting bolts, and then remove radiator core support upper.
Installation
Install in the reverse order of removal.
RADIATOR CORE SUPPORT LOWER
Removal
1.
Remove front bumper fascia and apron bracket. Refer to
EXT-15, "Removal and Installation"
2.
Remove air lower guide fixing clips, and then remove air lower guide.
: Vehicle front
JMKIB3661ZZ
: Vehicle front
JMKIB3662ZZ
: Vehicle front
JMKIB3005ZZ
DLK-578
< REMOVAL AND INSTALLATION >
[TYPE 2]
RADIATOR CORE SUPPORT
3.
Using strings (A), hang inlet hose
and inlet hose
together
with charge air cooler.
CAUTION:
Never damage inlet hoses and charge air cooler.
4.
Use belts (A) to suspend radiator and condenser to prevent
them from falling as shown in the figure.
CAUTION:
Never damage radiator and condenser.
5.
Remove radiator core support lower mounting bolts, and then remove radiator core support lower.
Installation
Install in the reverse order of removal.
JMKIB3663ZZ
JMKIB3664ZZ
FRONT FENDER
DLK-579
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT FENDER
Exploded View
INFOID:0000000010728119
FRONT FENDER
FRONT FENDER : Removal and Installation
INFOID:0000000010728120
REMOVAL
1.
Remove front fender protector. Refer to
EXT-35, "FENDER PROTECTOR : Removal and Installation"
2.
Remove sill cover. Refer to
EXT-62, "Removal and Installation"
3.
Remove front bumper fascia assembly and bumper side bracket. Refer to
EXT-15, "Removal and Installa-
4.
Remove front combination lamp. Refer to
EXL-191, "Removal and Installation"
(LED headlamp),
376, "Removal and Installation"
(halogen headlamp).
5.
Remove front fender cover. Refer to
DLK-580, "FENDER COVER : Removal and Installation"
.
Front fender cover
Front fender spacer
Front hood seal
Front fender bracket
Front fender assembly
Front fender seal
: Pawl
JMKIB3665ZZ
DLK-580
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT FENDER
6.
Remove front hood seal fixing clips
and front fender spacers
, and then remove front hood seal
.
7.
Remove mounting bolts of front fender assembly.
8.
Remove front fender stiffener
from the vehicle body while
carefully pulling upper portion of front fender
toward vehicle
outside.
9.
Remove front fender assembly.
CAUTION:
A viscous urethane foam is installed on the back surface of front fender. When removing the front
fender, be careful to not deform the front fender while performing the procedure and removing the
viscous urethane foam a little at a time.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• After installation, adjust the following part.
- Hood assembly: Refer to
DLK-567, "HOOD ASSEMBLY : Adjustment"
.
- Front door: Refer to
DLK-584, "DOOR ASSEMBLY : Adjustment"
• After installation, apply the touch-up paint (the body color) onto the head of front fender mounting
bolts.
FENDER COVER
FENDER COVER : Removal and Installation
INFOID:0000000010728121
REMOVAL
1.
Fully open hood assembly.
JMKIB3666ZZ
: Vehicle front
JMKIA5633ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст