Nissan X-Trail 32. Instruction — part 532
AUTOMATIC BACK DOOR CLOSE SWITCH
DLK-469
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK AUTOMATIC BACK DOOR CLOSE SWITCH
DLK-469, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace automatic back door close switch.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000010717515
1.
CHECK AUTOMATIC BACK DOOR CLOSE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect automatic back door close switch connector.
3.
Check continuity between automatic back door close switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace automatic back door close switch.
Automatic back door close switch
Ground
Continuity
Connector
Terminal
D173
2
Existed
Automatic back door close switch
Condition
Continuity
Terminal
1
2
Automatic back door
close switch
Pressed
Existed
Released
Not existed
DLK-470
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
AUTOMATIC BACK DOOR SWITCH
AUTOMATIC BACK DOOR SWITCH
Component Function Check
INFOID:0000000010717516
1.
CHECK FUNCTION
1.
Turn ignition switch ON.
2.
Select “AUTO BACK DOOR” using CONSULT.
3.
Select “AUTO BD SW” in “DATA MONITOR” mode.
4.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Automatic back door switch is OK.
NO
>> Refer to
DLK-470, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010717517
1.
CHECK AUTOMATIC BACK DOOR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect automatic back door switch connector.
3.
Check voltage between automatic back door switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK AUTOMATIC BACK DOOR SWITCH CIRCUIT
1.
Disconnect automatic back door control unit connector.
2.
Check continuity between automatic back door control unit harness connector and automatic back door
switch harness connector.
3.
Check continuity between automatic back door control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control unit. Refer to
DLK-633, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK AUTOMATIC BACK DOOR SWITCH GROUND CIRCUIT
Check continuity between automatic back door switch harness connector and ground.
Monitor item
Condition
Status
AUTO BD SW
Automatic back door switch
Pressed
ON
Released
OFF
(+)
(–)
Voltage
(Approx.)
Automatic back door switch
Connector
Terminal
M58
1
Ground
12.6 V
Automatic back door control unit
Automatic back door switch
Continuity
Connector
Terminal
Connector
Terminal
B24
22
M58
1
Existed
Automatic back door control unit
Ground
Continuity
Connector
Terminal
B24
22
Not existed
AUTOMATIC BACK DOOR SWITCH
DLK-471
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK AUTOMATIC BACK DOOR SWITCH
DLK-471, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace automatic back door switch.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000010717518
1.
CHECK AUTOMATIC BACK DOOR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect automatic back door switch connector.
3.
Check continuity between automatic back door switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace automatic back door switch.
Automatic back door switch
Ground
Continuity
Connector
Terminal
M58
2
Existed
Automatic back door switch
Condition
Continuity
Terminal
1
2
Automatic back door switch
Pressed
Existed
Released
Not existed
DLK-472
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
AUTOMATIC DOOR MAIN SWITCH
AUTOMATIC DOOR MAIN SWITCH
Component Function Check
INFOID:0000000010717519
1.
CHECK FUNCTION
1.
Turn ignition switch ON.
2.
Select “AUTO BACK DOOR” using CONSULT.
3.
Select “MAIN SW” in “DATA MONITOR” mode.
4.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Automatic door main switch is OK.
NO
>> Refer to
DLK-472, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010717520
1.
CHECK AUTOMATIC BACK DOOR MAIN SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect automatic back door main switch connector.
3.
Check voltage between automatic back door main switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK AUTOMATIC BACK DOOR MAIN SWITCH CIRCUIT
1.
Disconnect automatic back door control unit connector.
2.
Check continuity between automatic back door control unit harness connector and automatic back door
main switch harness connector.
3.
Check continuity between automatic back door control unit connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control unit. Refer to
DLK-633, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK AUTOMATIC BACK DOOR MAIN SWITCH GROUND CIRCUIT
Check continuity between automatic back door main switch connector and ground.
Monitor item
Condition
Status
MAIN SW
Automatic door main switch
ON
ON
OFF
OFF
(+)
(–)
Voltage
(Approx.)
Automatic back door main switch
Connector
Terminal
M54
1
Ground
12.2 V
Automatic back door control unit
Automatic back door main switch
Continuity
Connector
Terminal
Connector
Terminal
B24
10
M54
1
Existed
Automatic back door control unit
Ground
Continuity
Connector
Terminal
B24
10
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст