Nissan X-Trail 32. Instruction — part 1480
INSTRUMENT PANEL ASSEMBLY
IP-15
< REMOVAL AND INSTALLATION >
[LHD MODELS]
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
[]: Number indicates step in removal procedure.
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 minutes
or more.
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Always apply the parking brake before performing removal and installation.
1.
Remove center console assembly. Refer to
IP-25, "Removal and Installation"
.
2.
Remove A/C control (automatic air conditioning) or A/C control (A/C amp.) (instruction air conditioning).
Refer to
HAC-125, "Removal and Installation"
(automatic air conditioning) or
(instruction air conditioning)
3.
Remove instrument lower panel center.
a.
Disengage fixing pawls and metal clips, and then remove instru-
ment lower panel center.
b.
Disconnect harness connector and aspirator duct (if equipped).
4.
Remove instrument finisher E.
Cluster lid C (without audio system)
[12]
Instrument mask LH
[13]
[3]
Fuse block lid
[14]
[4]
Hood lock control handle
[15]
[5]
instrument lower panel LH
[16]
[6]
Side ventilator grille LH
[17]
[7]
Instrument finisher A
[18]
[8]
Cluster lid A
[19]
[9]
Combination meter
[20]
[10]
Sunload sensor (if equipped)
[21]
Front pillar garnish LH and RH
[22]
Instrument garnish
[23]
Center ventilator grille
[24]
Driver air bag module
[25]
Steering wheel
[26]
Steering column cover
[27]
Spiral cable
[28]
Steering angle sensor (if equipped)
[29]
Combination switch
[30]
Passenger air bag module mounting bolt
[31]
Passenger air bag module harness connector
[32]
Instrument panel assembly
[33]
: Pawl
: Metal clip
JMJIA9814ZZ
IP-16
< REMOVAL AND INSTALLATION >
[LHD MODELS]
INSTRUMENT PANEL ASSEMBLY
a.
Disengage fixing metal clips and pawl, and then remove instru-
ment finisher E.
b.
Remove push-button ignition switch harness connector. (with Intelligent Key System)
c.
Remove the following part after removing instrument finisher E. (with Intelligent Key System)
Push-button ignition switch: Refer to
PCS-116, "Removal and Installation"
5.
Remove glove box.
a.
Disengage glove box damper arm from glove box according to
the numerical order 1
→
2 indicated by arrows as shown in the
figure.
b.
Open the glove box approximately 50 mm.
c.
Pull up glove box toward the direction of arrow as shown in the
figure to disengage pawls from instrument panel.
6.
Disengage fixing pawls, and then remove instrument mask RH.
7.
Remove glove box cover.
: Pawl
: Metal clip
JMJIB0125ZZ
JMJIA9817ZZ
: Pawl
JMJIB0130ZZ
: Pawl
JMJIB0121ZZ
INSTRUMENT PANEL ASSEMBLY
IP-17
< REMOVAL AND INSTALLATION >
[LHD MODELS]
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
a.
Remove fixing screws
.
b.
Disengage fixing metal clips and pawls, and then remove glove
box cover by arrow as shown in the figure.
c.
Disconnect glove box lamp harness connector.
d.
Remove the following part after removing glove box.
• Glove box lamp: Refer to
.
• Air bag cutoff switch: refer to
SR-35, "Removal and Installation"
8.
Remove side ventilator grille RH. Refer to
VTL-12, "SIDE DEFROSTER GRILLE : Removal and Installa-
9.
Disengage fixing clips and pawl, and then remove instrument
finisher B.
10. Disengage fixing metal clips and pawls, and then remove instrument upper panel assist.
11. Remove audio unit or AV control unit. Refer to the following. (with audio system)
• Audio unit: Refer to
AV-51, "Removal and Installation"
(BASE AUDIO).
• NAVI control unit: Refer to
AV-262, "Removal and Installation"
(WITH NAVIGATION).
: Pawl
: Metal clip
JMJIB0234ZZ
: Clip
: Pawl
JMJIB0124ZZ
: Pawl
: Metal clip
JMJIB0233ZZ
IP-18
< REMOVAL AND INSTALLATION >
[LHD MODELS]
INSTRUMENT PANEL ASSEMBLY
12. Disengage fixing pawls and metal clips, and then remove cluster
lid C by arrow as shown in the figure. (without audio system)
13. Remove instrument mask LH.
a.
Apply protective tape (A) on the part to protect it from damage.
b.
Disengage fixing pawls using remover tool (A), and then remove
instrument mask.
14. Disengage fixing pawls, and then remove fuse block lid by arrow
as shown in the figure.
15. Remove hood lock control handle. Refer to
DLK-607, "HOOD LOCK CONTROL HANDLE : Removal and
(with Intelligent Key system) or
DLK-912, "HOOD LOCK CONTROL HANDLE : Removal and
(without Intelligent Key system).
16. Remove instrument lower panel LH.
: Pawl
: Metal clip
JMJIA9779ZZ
JMJIB0119ZZ
: Pawl
JMJIB0120ZZ
: Pawl
JMJIB0122ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст