Nissan X-Trail 32. Instruction — part 1303
FSU-16
< REMOVAL AND INSTALLATION >
FRONT COIL SPRING AND STRUT
2.
Check wheel alignment. Refer to
.
3.
Adjust neutral position of steering angle sensor. Refer to
.
Disposal
INFOID:0000000010822757
1.
Set strut assembly horizontally to the ground with the piston rod fully extracted.
2.
Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position (
) from top
as shown in the figure to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction show by arrow.
• Directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3.
Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
A
: 20 – 30 mm (0.79 – 1.18 in)
JMEIA0225ZZ
TRANSVERSE LINK
FSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
TRANSVERSE LINK
Exploded View
INFOID:0000000010822758
Removal and Installation
INFOID:0000000010822759
REMOVAL
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Remove under cover. Refer to
EXT-39, "ENGINE UNDER COVER : Exploded View"
.
3.
Separate transverse link from steering knuckle.
• 2WD: Refer to
FAX-11, "Removal and Installation"
.
• 4WD: Refer to
FAX-72, "Removal and Installation"
.
4.
Remove transverse link from suspension member.
NOTE:
When removing transverse link, the stabilizer interferes with the
transverse link mounting bolt (
). Move the stabilizer to the
position where the mounting bolt can be removed. Refer to
19, "Removal and Installation"
5.
Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Never reuse transverse link mounting nut.
• Perform final tightening of bolts and nuts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Perform inspection after installation. Refer to
.
Front suspension member
Transverse link
Steering knuckle
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Vehicle front
JSEIA0895GB
SEIA0633J
FSU-18
< REMOVAL AND INSTALLATION >
TRANSVERSE LINK
Inspection
INFOID:0000000010822760
INSPECTION AFTER REMOVAL
Check the following items, and replace the parts if necessary.
Transverse Link
• Transverse link and bushing for deformation, cracks or damage.
• Ball joint boot for cracks or other damage, and also for grease leakage.
Swing Torque
1.
Instructionly move ball stud to confirm it moves smoothly with no binding.
2.
Move ball stud at least ten times by hand to check for smooth movement.
3.
Hook a spring balance (A) at cutout on ball stud
. Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
• If swing torque exceeds standard range, replace transverse link
assembly.
Axial End Play
1.
Move ball stud at least ten times by hand to check for smooth movement.
2.
Move tip of ball stud in axial direction to check for looseness.
• If axial end play exceeds the standard value, replace transverse link assembly.
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
.
2.
Adjust neutral position of steering angle sensor. Refer to
.
Swing torque
: Refer to
.
Measurement on
spring balance
: Refer to
JPEIA0138ZZ
Axial end play
: Refer to
FRONT STABILIZER
FSU-19
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
FRONT STABILIZER
Exploded View
INFOID:0000000010822761
Removal and Installation
INFOID:0000000010822762
REMOVAL
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Remove under cover. Refer to
EXT-39, "ENGINE UNDER COVER : Exploded View"
.
3.
Remove steering outer socket from steering knuckle. Refer to
ST-22, "Removal and Installation"
.
4.
Remove stabilizer connecting rod.
5.
Remove member stay. Refer to
FSU-22, "Removal and Installation"
6.
Remove rear torque rod.
• MR20DD: Refer to
EM-56, "Removal and Installation"
• QR25DE: Refer to
EM-200, "Removal and Installation"
.
• R9M: Refer to
EM-366, "Removal and Installation"
.
7.
Separate steering gear assembly from steering shaft. Refer to
ST-22, "Removal and Installation"
Stabilizer clamp
Stabilizer bushing
Stabilizer bar
Front suspension member
Stabilizer connecting rod
Strut
: N·m (kg-m, ft-lb)
: Vehicle front
JSEIA0897GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст