Nissan X-Trail 32. Instruction — part 1239
FRONT BUMPER
EXT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000010787437
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
REMOVAL
1.
Fully open hood assembly.
2.
Remove front grille. Refer to
EXT-22, "Removal and Installation"
3.
Remove front bumper fascia fixing clips
of bumper upper
side.
4.
Remove engine under cover fixing clips
of bumper lower side.
5.
Remove front spoiler. Refer to
EXT-28, "Removal and Installation"
6.
Remove front bumper fascia fixing screws
lower side of the
bumper both end.
7.
Remove front side of front fillet molding (LH and RH). Refer to
EXT-32, "FRONT FILLET MOLDING :
.
Front bumper finisher LH
(without front fog lamp)
Bumper bracket cover
Headlamp washer cover LH
Front bumper fascia
Front fog lamp LH
Apron bracket
Front bumper side bracket LH
Front bumper stay LH
Front fog lamp RH
Front bumper grille
: Pawl
: N·m (kg-m, ft-lb)
,
,
,
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB2790ZZ
: Vehicle front
JMKIB2791ZZ
: Vehicle front
JMKIB3778ZZ
EXT-16
< REMOVAL AND INSTALLATION >
FRONT BUMPER
8.
Remove grommet
front side of fender protector (LH and RH).
9.
Remove front bumper fascia fixing screws
(LH and RH).
10. Apply protective tapes (A) on the part to protect it from damage.
11. Pull bumper fascia side toward the vehicle side to disengage the
fitting of bumper side bracket and bumper fascia side according
to the numerical order 1
→
2 as shown by the arrows in the fig-
ure.
CAUTION:
When removing bumper fascia assembly, 2 workers are
required so as to prevent it from dropping.
12. Disconnect front fog lamp harness connectors (LH and RH). (if equipped)
13. Disconnect front sonar sensor harness connectors (LH and RH). (if equipped)
14. Disconnect headlamp washer tube connector, and then remove headlamp washer tube from washer
pump. (if equipped)
15. Remove front bumper fascia assembly.
CAUTION:
When removing bumper fascia assembly, 2 workers are required so as to prevent it from dropping.
16. Remove the following parts after removing front bumper fascia assembly.
• Front fog lamp. Refer to the following. (if equipped)
- LED HAEDLAMP: Refer to
EXL-193, "Removal and Installation"
- HALOGEN HEADLAMP: Refer to
EXL-379, "Removal and Installation"
: Vehicle front
JMKIB2793ZZ
: Vehicle front
JMKIB2794ZZ
JMKIB2795ZZ
: Pawl
JMKIB2796ZZ
FRONT BUMPER
EXT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
• Front sonar sensor. Refer to the following. (if equipped)
- WITH PARK ASSIST: Refer to
SN-239, "FRONT : Removal and Installation"
.
- WITHOUT PARK ASSIST: Refer to
SN-113, "FRONT : Removal and Installation"
.
• Headlamp washer tube. Refer to
WW-107, "WASHER TUBE : Removal and Installation"
. (if equipped)
• Headlamp washer nozzle. Refer to
WW-105, "WASHER NOZZLE : Removal and Installation"
. (if
equipped)
• Front bumper side bracket (LH and RH).
• Front bumper finisher (LH and RH).
• Front bumper grille.
• Front bumper molding.
• Bumper bracket cover.
17. Remove front bumper energy absorber.
18. Remove apron bracket mounting nuts and fixing clips, and then remove apron bracket.
19. Remove front bumper reinforcement.
a.
Remove harness clip.
b.
Disengage ambient sensor fixing pawl.
c.
Remove intelligent key warning buzzer mounting bolt. (with intelligent key system)
d.
Remove distance radar mounting bolts. (if equipped)
e.
Remove front bumper reinforcement mounting nuts, and then remove front bumper reinforcement.
20. Remove front bumper stay mounting bolts, and then remove front bumper stay (LH and RH).
INSTALLATION
Note the following items, and then install in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation status.
• Fitting adjustment cannot be performed.
JMKIB2797ZZ
Portion Clearance
Surface
height
difference
Front bumper fascia – front grille
–
0.1 – 3.0 mm
(0.004 – 0.118 in)
—
–
0.1 – 3.0 mm
(0.004 – 0.118 in)
—
Front bumper fascia – Front
combination lamp
–
0.1 – 3.0 mm
(0.004 – 0.118 in)
—
Front bumper fascia – Front
fender panel
–
0.1 – 1.0 mm
(0.004 – 0.039 in)
(
−
0.3) – (+1.7) mm
[(
−
0.012) – (+0.067) in]
EXT-18
< REMOVAL AND INSTALLATION >
REAR BUMPER
REAR BUMPER
Exploded View
INFOID:0000000010787438
Removal and Installation
INFOID:0000000010787439
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
Rear bumper side bracket LH
Grommet
Rear bumper stay LH
Rear bumper fascia
Reflex reflector LH
Rear fog lamp (if equipped)
Rear bumper finisher
(if equipped)
Reflex reflector RH
Rear bumper reinforcement
Rear bumper stay RH
Rear bumper side bracket RH
: Pawl
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
,
,
,
,
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIB3753GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст