Nissan X-Trail 32. Instruction — part 128
BR-106
< REMOVAL AND INSTALLATION >
[RHD]
FRONT DISC BRAKE
8.
Install the lower sliding pin bolt and tighten it to the specified
torque.
9.
Depress the brake pedal several times to check that no drag feel is present for the front disc brake. Refer
to
BR-106, "BRAKE PAD (1 PISTON TYPE) : Inspection"
.
10. Install tires. Refer to
WT-61, "Removal and Installation"
BRAKE PAD (1 PISTON TYPE) : Inspection
INFOID:0000000010838596
INSPECTION AFTER REMOVAL
• Replace the shims and shim covers if rust is excessively attached.
• Eliminate rust on the pad return spring, pad retainers and the torque member. Replace them if rust is exces-
sively attached.
INSPECTION AFTER INSTALLATION
• Check a drag of front disc brake. If any drag is found, follow the procedure described below.
1.
Remove brake pads. Refer to
BR-103, "BRAKE PAD (1 PISTON TYPE) : Removal and Installation"
.
2.
Press the pistons. Refer to
BR-103, "BRAKE PAD (1 PISTON TYPE) : Removal and Installation"
.
3.
Install brake pads. Refer to
BR-103, "BRAKE PAD (1 PISTON TYPE) : Removal and Installation"
4.
Depress the brake pedal several times.
5.
Check a drag of front disc brake again. If any drag is found, disassemble the cylinder body and replace if
necessary. Refer to
BR-112, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Disassembly and
• Burnish contact surfaces brake pads and disc rotor after refinishing or replacing brake pads, or if a soft pedal
occurs at very low mileage. Refer to
BR-81, "BRAKE PAD : Inspection and Adjustment"
.
BRAKE PAD (2 PISTON TYPE)
BRAKE PAD (2 PISTON TYPE) : Exploded View
INFOID:0000000010838969
JPFIA0832ZZ
JSFIA2246GB
FRONT DISC BRAKE
BR-107
< REMOVAL AND INSTALLATION >
[RHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
Molykote is a registered trademark of Dow Corning Corporation.
BRAKE PAD (2 PISTON TYPE) : Removal and Installation
INFOID:0000000010838970
REMOVAL
WARNING:
Since dust covering the front and rear brakes has an affect on human body, the dust must be removed
with a dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never depress the brake pedal while removing the brake pads because the piston may pop out.
• If the brake fluid or grease adheres to the brake caliper assembly and disc rotor, quickly wipe it off.
1.
Remove tires with power tool.
2.
Remove lower sliding pin bolt.
3.
Suspend the cylinder body with suitable wire so that the brake
hose will not stretch.
4.
Remove the brake pads, shims, shim covers and pad retainer
(as a set with pad return spring)
from the torque member
.
CAUTION:
• Remove pad retainer together with pad return springs.
• Never deform the pad return springs and pad retainer
when removing the pad retainer from the torque member.
• Never damage the piston boots.
• Never drop the brake pads, shims and shim covers.
• Remember each position of the removed brake pads.
Cylinder body
Inner shim cover
Inner shim
Inner pad (with pad wear sensor)
Return spring
Pad retainer
Torque member
Outer pad
Outer shim
Outer shim cover
1: Apply MOLYKOTE
®
AS 880N or silicone-based grease.
2: Apply MOLYKOTE
®
7439 or equivalent.
: N·m (kg-m, ft-lb)
JPFIA0832ZZ
JPFIA0850ZZ
JPFIA0118ZZ
BR-108
< REMOVAL AND INSTALLATION >
[RHD]
FRONT DISC BRAKE
5.
Remove the pad return springs
from the pad retainer
.
CAUTION:
Never deform the pad return springs when removing the
pad return springs from the pad retainer.
6.
Perform inspection after removal. Refer to
PAD (2 PISTON TYPE) : Inspection"
INSTALLATION
WARNING:
Since dust covering the front and rear brakes has an affect on human body, the dust must be removed
with a dust collector. Never splatter the dust with an air blow gun.
CAUTION:
• Never depress the brake pedal while removing the brake pads because the piston may pop out.
• If the brake fluid or grease adheres to the brake caliper assembly and disc rotor, quickly wipe it off.
1.
Install the pad return springs
to pad retainer
if the pad
return springs has been removed.
CAUTION:
Never deform the pad return springs.
2.
Apply MOLYKOTE
®
7439 or equivalent to the match face
between the pad retainers
and torque member
if the pad
retainers has been removed.
Molykote is a registered trademark of Dow Corning Corporation.
3.
Install the pad retainer (upper side with pad return spring) to
torque member if the pad retainers has been removed.
CAUTION:
• Securely assemble the pad retainers so that it will not be
lifted up from the torque member.
• Never deform the pad retainers and pad return springs.
4.
Apply MOLYKOTE
®
AS880N or silicone-based grease to the
matching faces
between the shim
and the shim cover
,
and install the shim and the shim covers to the brake pad
.
CAUTION:
Always replace the shims and shim covers when replacing
the brake pad.
Molykote is a registered trademark of Dow Corning Corporation.
: Disc rotor side
JSFIA2329ZZ
: Disc rotor side
JSFIA2329ZZ
JSFIA1938ZZ
JSFIA1330ZZ
FRONT DISC BRAKE
BR-109
< REMOVAL AND INSTALLATION >
[RHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
5.
Apply MOLYKOTE
®
7439 or equivalent to the match face
between the brake pad
and torque member
.
Molykote is a registered trademark of Dow Corning Corporation.
6.
Install the brake pads to the torque member.
CAUTION:
Both inner and outer pads have a pad return system.
Securely push the pad return spring
into the disc rotor
side of brake pad
.
7.
Install cylinder body to torque member.
CAUTION:
• Never damage the piston boot.
• When replacing brake pad with new one, check a brake fluid level in the reservoir tank because
brake fluid returns to reservoir tank when pressing piston in.
NOTE:
Use a disc brake piston tool to easily press piston.
8.
Install the lower sliding pin bolt and tighten it to the specified
torque.
9.
Depress the brake pedal several times to check that no drag feel is present for the front disc brake. Refer
to
BR-109, "BRAKE PAD (2 PISTON TYPE) : Inspection"
.
10. Install tires. Refer to
WT-61, "Removal and Installation"
.
BRAKE PAD (2 PISTON TYPE) : Inspection
INFOID:0000000010838971
INSPECTION AFTER REMOVAL
• Replace the shims and shim covers if rust is excessively attached.
• Eliminate rust on the pad return spring, pad retainers and the torque member. Replace them if rust is exces-
sively attached.
INSPECTION AFTER INSTALLATION
• Check a drag of front disc brake. If any drag is found, follow the procedure described below.
JSFIA1337ZZ
JSFIA2330ZZ
JPFIA0832ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст