Nissan X-Trail 32. Instruction — part 1617
MWI-150
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
INFORMATION DISPLAY
INFORMATION DISPLAY : Description
INFOID:0000000010715042
DISTANCE TO EMPTY
The calculated distance to empty may differ from the actual distance to empty if the refueling amount is
approximately 5 (1-1/8 Imp gal) or less. This is because the refuel control (moves the fuel gauge needle
quicker than normal judging that the driver is refueling the vehicle) is not performing.
AMBIENT TEMPERATURE
The displayed ambient temperature on the information display may differ from the actual temperature because
it is a corrected value calculated from the ambient sensor signal by the combination meter. Refer to
"INFORMATION DISPLAY : System Description"
for details on the correction process.
MWI
COMBINATION METER
MWI-151
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
REMOVAL AND INSTALLATION
COMBINATION METER
Exploded View
INFOID:0000000010715043
REMOVAL
(LHD models), or
(RHD models).
DISASSEMBLY
Removal and Installation
INFOID:0000000010715044
REMOVAL
1.
Disconnect the battery cable from the negative terminal..
2.
Remove cluster lid A. Refer to
IP-14, "Removal and Installation"
(LHD models) or
(RHD models).
3.
Remove the mounting screws
of the combination meter
.
Unified meter control unit
Front cover
JSNIA6660ZZ
JSNIA7202ZZ
MWI-152
< REMOVAL AND INSTALLATION >
COMBINATION METER
4.
Pull out the combination meter straight to desengage resin clips.
(The figure shows the clip positions on the back of the combina-
tion meter.)
CAUTION:
Never damage the front cover.
5.
Turn combination meter in the direction shown by arrow and dis-
connect the connector to remove combination meter from vehi-
cle.
CAUTION:
Never damage the front cover.
INSTALLATION
Installation is in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000010715045
DISASSEMBLY
1.
Unlatch the pawls on the side (2 pawls) and the bottom (3 pawls)
of combination meter to allow the front cover to become slightly
released.
2.
Insert removal tool into the clearance (
and
) between front
cover and meter control unit assembly and unlatch pawls by
turning the tool in the way of widening the clearance.
CAUTION:
Wrap the removal tools with protective tape to prevent
scratches.
JSNIA6662ZZ
JSNIA7203ZZ
: Pawl
JSNIA6664ZZ
JSNIA6665ZZ
MWI
COMBINATION METER
MWI-153
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
3.
Insert removal tool into
and
to unlatch the pawls.
CAUTION:
• Wrap the removal tools with protective tape to prevent
scratches.
• Never damage the front cover.
4.
Pull the front cover straight to remove it from the unified meter control unit.
CAUTION:
• Never damage the front cover.
• Never touch the inside of front cover, pointer, the display and the printed area of the dial during
the work.
• Keep away from magnetic sources.
ASSEMBLY
Install the front cover straight to the unified meter control unit and engage all the pawl.
CAUTION:
• Never damage the front cover.
• Never touch the inside of front cover, pointer, the display and the printed area of the dial during the
work.
• Keep away from magnetic sources.
: Pawl
JSNIA6666ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст