Nissan X-Trail 32. Instruction — part 282
CHG-44
< REMOVAL AND INSTALLATION >
[TYPE 2]
ALTERNATOR
REMOVAL AND INSTALLATION
ALTERNATOR
MR20DD
MR20DD : Exploded View
INFOID:0000000010957571
MR20DD : Removal and Installation
INFOID:0000000010957572
REMOVAL
1.
Disconnect battery cable from negative terminal. Refer to
PG-142, "EXCEPT FOR R9M : Removal and
.
2.
Remove drive belt. Refer to
EM-22, "Removal and Installation"
.
3.
Remove washer tank inlet. Refer to
WW-91, "Removal and Installation"
.
4.
Remove low pressure flexible hose bracket mounting bolt
and
nut .
5.
Remove ground cable clip
.
“B” terminal nut
“B” terminal harness
Alternator
Alternator mounting bolt (upper)
Alternator mounting bolt (lower)
Alternator harness connector
: N·m (kg-m, ft-lb)
JMMIA0640GB
: Vehicle front
JMMIA1601ZZ
CHG
ALTERNATOR
CHG-45
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
6.
Remove “B” terminal nut
and “B” terminal harness.
7.
Disconnect alternator harness connector
and harness clips
.
8.
Remove alternator mounting bolt (upper).
9.
Completely loosen alternator mounting bolt (lower), and pull it out until the bolt head is in contact with the
side member. And then, remove the alternator by pulling it forward.
NOTE:
The alternator can be removed together with the bolts by pulling it forward and using the alternator bracket
bolt hole cutout.
10. Remove alternator upward from the vehicle.
CAUTION:
• Never put excessive power on low pressure flexible hose
and high pressure pipe.
• Never bend ground cable.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Temporarily tighten the alternator bolts in order from the lower to the upper, and then tighten them in
order from the upper to the lower.
• For the alternator, the front side (pulley side) surface is the reference surface. Fit the reference sur-
face to the alternator mounting part, and then tighten the bolts.
• Be careful to tighten “B” terminal nut to the specified torque.
• Install alternator, and check tension of belt. Refer to
QR25DE
: Vehicle front
JMMIA1602ZZ
: Vehicle front
JMMIA1603ZZ
CHG-46
< REMOVAL AND INSTALLATION >
[TYPE 2]
ALTERNATOR
QR25DE : Exploded View
INFOID:0000000010957573
QR25DE : Removal and Installation
INFOID:0000000010957574
REMOVAL
1.
Disconnect battery cable from negative terminal. Refer to
PG-142, "EXCEPT FOR R9M : Removal and
.
2.
Remove drive belt. Refer to
EM-166, "Removal and Installation"
3.
Remove washer tank inlet. Refer to
WW-91, "Removal and Installation"
.
4.
Remove ground cable bracket mounting bolt
, and then move
ground cable bracket
to a location where it does not inhibit
work.
CAUTION:
Never bend ground cable.
5.
Remove low pressure flexible hose bracket mounting bolts
and nut
.
6.
Remove “B” terminal nut and disconnect “B” terminal harness.
Alternator harness connector
“B” terminal harness
“B” terminal nut
Alternator
Alternator mounting bracket
: N·m (kg-m, ft-lb)
JMMIA1615GB
: Vehicle front
JMMIA1805ZZ
: Vehicle front
JMMIA1806ZZ
CHG
ALTERNATOR
CHG-47
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
7.
Disconnect alternator harness connector.
8.
Remove alternator mounting bolts.
9.
Remove alternator upward from the vehicle.
CAUTION:
Never strong force to low pressure flexible hose and high pressure pipe.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Temporarily tighten the alternator bolts in order from the lower side to the upper side, and then
tighten them in order from the upper side to the lower side.
• For the alternator, the front side (pulley side) surface is the reference surface. Fit the reference sur-
face to the alternator mounting part, and then tighten the bolts.
• Be careful to tighten “B” terminal nut to the specified torque.
• Install alternator and check tension of belt. Refer to
.
NOTE:
Tighten mounting bolts according to the following procedure for
installing alternator bracket.
JMMIA1414ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст