Nissan X-Trail 32. Instruction — part 926
SYSTEM
EC-833
< SYSTEM DESCRIPTION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0641
Sensor power supply
• EGR valve is closed position
• Throttle control motor is opened
• The pressure downstream turbo exists then the limit: Otherwise cut regu-
lation turbo
• Limited upstream turbine pressure regulation if the sensor is present: Oth-
erwise, the boost pressure regulation is cut
• Torque limitation
• Airflow regulation cut off
• CSF regeneration forbidden
• CCSL deactivation with dashboard message
• Freeshift inhibited
• Increased idle speed
• After sales routines forbidden
P0651
• Air conditioner deactivation
• Torque limitation
• CCSL deactivation with dashboard message
• Freeshift inhibited
• After sales routines forbidden
• FAN 2 activation
P0697
• EGR valve is closed position
• Throttle control motor is opened
• Rail pressure limitation
• CSF regeneration forbidden
• After sales routines forbidden
• CCSL deactivation with dashboard message
• Freeshift inhibited
• ESP deactivated and AGB in limp home mode
P0833
DPF pressure sensor
CC/SL not available
P1010
P1012
P1013
Intake manifold runner control valve
Stop intake manifold runner control valve control (Fully open position)
P1011
• Stop intake manifold runner control valve control (Fully open position)
• CCSL deactivation
• Freeshift inhibition
P1453
DPF pressure sensor
• EGR valve is closed position
• Throttle control motor is opened
• Prohibit DPF regeneration
P1480
P1481
P1482
P1483
Exhaust electric throttle control actuator
• EGR valve is closed position
• Throttle control motor is opened
• Airflow regulation cut off
• CSF regeneration forbidden
• Compression test routine forbidden
• CCSL deactivation with dashboard message
• Freeshift inhibited
P1484
P1485
P1486
P1487
P1488
Low pressure EGR volume control valve
• EGR valve is closed position
• Throttle control motor is opened
• CSF regenerations forbidden
• CCSL deactivation with dashboard message
• Freeshift inhibited
P1489
• EGR valve is closed position
• Throttle control motor is opened
• Temperature sensor after EGR cooler overheat signal diagnostic set of
data to call the failure manag.
P1544
Exhaust gas temperature sensor 2 circuit
• EGR valve is closed position
• Throttle control motor is opened
• Prohibit DPF regeneration
P1620
ECM
Stop closed-loop control
DTC No.
Detected items
Engine operating condition in fail-safe mode
EC-834
< SYSTEM DESCRIPTION >
[R9M]
SYSTEM
STOP/START SYSTEM
ENGINE SPEED CONTROL
P1641
P1642
P1643
Thermoplunger circuit
Stop thermoplunger control
P2002
Diesel particulate filter
• EGR valve is closed position
• Throttle control motor is opened
• Prohibit DPF regeneration
P2120
Accelerator pedal position sensor 2 circuit
• Torque limitation
• Freeshift inhibited
• CCSL deactivation (considered as abnormal with dashboard message)
• Aftersales and factory routines inhibited
P2226
Atmosphere pressure sensor
• EGR valve is closed position
• Throttle control motor is opened
• Prohibit DPF regeneration
P2263
Turbocharger boost pressure sensor circuit
• EGR valve is closed position
• Throttle control motor is opened
• Torque limitation
• CCSL deactivation (considered as abnormal with dashboard message)
• Freeshift is inhibited
• Wastegate activation is inhibited
• ESP deactivation
• CSF regeneration forbidden
P2452
Diesel particulate filter pressure sensor cir-
cuit
• EGR valve is closed position
• Throttle control motor is opened
• Prohibit DPF regeneration
P253F
• CSF regeneration is forbidden
• Torque limitation
• EGR valve is closed position
• Throttle control motor is opened
P2681
Engine coolant bypass valve circuit
• Engine cooling fan activation
• Throttle control motor is opened
• Prohibit start/stop system
• Stop EGR control
• Stop thermoplunger control
DTC No.
Detected items
Engine operating condition in fail-safe mode
DTC No.
Detected items
Stop/start system operating condition in fail safe mode
Idling or driving the vehi-
cle
Stop/start system operating
Stop
During cranking
(Restart)
U0298
Engine communication line
—
—
Prohibit the stop/start sys-
tem operation from the
next time
B1900
B1901
B1902
B1903
DC/DC converter
Prohibit the stop/start
system operation
Restart the engine
B1904
—
—
P0120
TP sensor
Prohibit the stop/start
system operation
Restart the engine
P0833
CPP switch
—
—
P1512
Starter motor
Prohibit the stop/start sys-
tem operation from the
next time
P1650
Starter motor relay2
Restart the engine or stall
the engine
P1655
P1656
Engine restart bypass relay
—
—
P2100
Throttle control motor relay
Prohibit the stop/start
system operation
SYSTEM
EC-835
< SYSTEM DESCRIPTION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
ENGINE SPEED CONTROL : System Description
INFOID:0000000010935561
SYSTEM DESCRIPTION
The engine speed control consists of the following functions:
• Curative anti-jerk
• Idle speed control
• Engine speed limitation
• Engine state
CURATIVE ANTI-JERK
This function aims to smooth the engine speed through torque corrections out of idle engine speed regulation.
The torque correction is made by the anti-jerk function to damp the engine speed vibrations caused by the
drive-line vibrations.
IDLE SPEED CONTROL
ECM calculates the engine idle speed set point and maintains the engine speed in order to follow the set point.
The engine idle speed set-point is computed for the following load and signal:
• Post treatment
- Diesel particulate filter
• Electric consumers
- Cooling fan
- Air heater (air conditioning system)
- Power window
- Alternator output current
• Automatic transmission
- Automatic transmission idle speed set point function (according to coolant temperature)
- Automatic transmission idle speed increase request
• Mechanical consumers
- Air conditioning
- Power steering
• Diagnosis and protection
- Diagnosis
- Engine protection by oil temperature survey
- CONSULT function
- Manifold absolute pressure sensor signal
The final engine idle speed set point is computed from each comsumer
′
s engine idle speed set point:
• The final corrective torque of the Idle Speed Regulation is obtained taking into account proportional, integral,
and derivative corrections.
ENGINE SPEED LIMITATION
ECM calculates the maximum engine speed set point and controls the maximum engine speed in order to fol-
low the set point.
• Fail-safe mode
• Maximum available engine speed
ENGINE STATE
ECM calculates the engine state from detected engine speed:
• Engine running
- Driving state
- Idling state
• Engine stalled
- Initial state
- Stalled state
POWERTRAIN COORDINATION CONTROL
POWERTRAIN COORDINATION CONTROL : System Description
INFOID:0000000010935562
SYSTEM DESCRIPTION
The powertrain coordination can be explained by following:
• Powertrain coordination inputs
• Preventive anti-jerk
EC-836
< SYSTEM DESCRIPTION >
[R9M]
SYSTEM
• Gear shift indicator (for details, refer to
EC-847, "GEAR SHIFT INDICATOR SYSTEM : System Descrip-
POWERTRAIN COORDINATION INPUTS
ECM detects following signals necessary to decide the torque set point:
• Gear position
• Torque request from automatic transmission
• Torque request from ABS system
• Brake pedal operation
• Status of Cruise Control System or Speed Limiter
PREVENTIVE ANTI-JERK
The main objective of the preventive anti-jerk function is to decrease discomforts of driver during depress the
accelerator pedal and during release the accelerator pedal.
The abrupt change of torque are delivered by engine excites a torsional natural frequencies of drive-line. It
causes vehicle jerking and acceleration fluctuations. And they are causes of perception and assessment of
performance and comfort for driver and the passengers.
The purpose of this function is to limit drive-line torque excitations. In fact, the engine torque set point is filtered
according to requirements of driveability.
TURBOCHARGER BOOST CONTROL
TURBOCHARGER BOOST CONTROL : System Description
INFOID:0000000010935563
DESCRIPTION
Turbocharger is used to increase the air pressure entering the engine. The turbocharger has two separate
chambers. The turbocharger consists of the following components:
• A chamber linked to the engine exhaust gas system
• A chamber linked to the engine air inlet system
• A turbine and a compressor, joined together by shaft.
The turbine, driven by exhaust gases, drives the compressor which compresses the inlet air.
CAUTION:
To stop the engine immediately after high-load driving, park the vehicle with the engine at idle before
turning OFF the ignition switch.
The boost pressure control is able to increase the manifold pressure with respect to the engine operating
point. The system has an electric solenoid valve connected on the vacuum circuit to control the flow of exhaust
gases through the turbine in order to generate high pressure in the boost circuit.
EGR SYSTEM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст