Nissan X-Trail 32. Instruction — part 1327
GW-26
< REMOVAL AND INSTALLATION >
SIDE WINDOW GLASS
SIDE WINDOW GLASS
Exploded View
INFOID:0000000010755100
Side window glass
Body side outer panel
Rear pillar inner panel
Painted surface primer
Luggage side upper finisher
Adhesive
Glass primer
Rear door weather-strip
Rear pillar inner reinforcement
: Clip
: Always replace after every disassembly.
JMKIB3569ZZ
SIDE WINDOW GLASS
GW-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Unit: mm (in)
Removal and Installation
INFOID:0000000010755101
REMOVAL
CAUTION:
Never damage body side outer panel.
1.
Remove luggage side upper finisher. Refer to
INT-45, "LUGGAGE SIDE UPPER FINISHER : Removal
2.
Disconnect harness connector
.
3.
Apply protective tape (A) on body side outer panel around side
window glass to protect painted surface from damage.
Portion
Primer range
Adhesive range
J
K
Side window glass – Body side outer panel
–
D
17.0
(0.669)
7.0
(0.276)
12.0
(0.472)
E
16.0
(0.630)
—
—
–
F
17.0
(0.669)
7.0
(0.276)
12.0
(0.472)
G
16.0
(0.630)
—
—
–
H
17.0
(0.669)
7.0
(0.276)
12.0
(0.472)
I
16.0
(0.630)
—
—
JMKIB3125ZZ
JMKIB3126ZZ
GW-28
< REMOVAL AND INSTALLATION >
SIDE WINDOW GLASS
4.
Insert a windshield cutter (A) between side window glass
and
body side outer panel
. Remove adhesive
by pulling the
windshield cutter, keeping the tip parallel to the edge of side win-
dow glass.
CAUTION:
Use piano wire to cut sealant if its difficult to use wind-
shield cutter.
5.
Remove adhesive using a piano wire.
a.
Pass the piano wire from passenger room to bonded area of side window glass using a wire pierce.
CAUTION:
Never damage surrounding parts.
b.
Tie both ends of the piano wire (B) to wire grip (A), etc..
c.
Remove adhesive by using piano wire alongside of side window glass and body side outer panel.
CAUTION:
Remove adhesive, 2 workers are required by all means.
6.
Remove side window glass.
INSTALLATION
CAUTION:
• Replace side window glass with a new part after removal. Never reuse side window glass.
• Never damage body side outer panel.
JMKIB3121ZZ
JMKIA9832ZZ
SIDE WINDOW GLASS
GW-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
1.
Use a cutter knife or scraper, and leave the of adhesive on the
body side approximately 2 mm (0.079 in) (A) to make adhesive
surface smooth.
CAUTION:
If the bonded area on the body is scratched, repair it using
a 2 liquid types urethane paint. Never use lacquer type
paint.
2.
Clean the bonded area on side window glass and body side outer panel using a white gasoline or
degreasing agent.
3.
Apply glass primer along the entire circumference of side window glass.
CAUTION:
• There are 2 types of primer. Never confuse the application methods.
- Painted surfaces primer
- Glass primer
• Use the sealing kit for glass application and the special holder for cartridge or similar tools.
• Dry glass primer according to the specification of adhesive kit.
NOTE:
The essential function of primers is to strengthen adhesion between the glass and the painted surface.
4.
Apply painted surface primer to the body side bonding surface.
CAUTION:
• If the body side bonding surface is repaired with 2 liquid types urethane paint, always apply the
primer after drying the paint.
• If painted surfaces primer adheres to a painted surface other than the bonding area, or if it over-
flows, quickly remove it with white gasoline or degreasing agent.
• Dry painted surface primer according to the specification of adhesive kit.
5.
Apply adhesive to entire circumference of side window glass by using a sealant gun.
NOTE:
Open adhesive by cutting off the nozzle tip and set it in a sealant gun.
6.
Press entire surface of side window glass lightly to fit it completely.
7.
Correct any adhesive overflow or shortage using a spatula to make the surface smooth.
CAUTION:
• After installing side window glass, keep the all door glass open until the adhesive is completely
cured.
• Never drive the vehicle before the adhesive is completely cured.
8.
Remove protective tape.
9.
Install removed parts.
CAUTION:
Check the mating area with surrounding parts. Adjust if necessary.
Inspection
INFOID:0000000010755102
WATER LEAKAGE INSPECTION
CAUTION:
• Dry adhesive according to the specification of adhesive kit, do the leaking check when adhesive is
stiffen.
• If leakage was found, start over from the beginning as side window glass removal, install and leaking
check.
JMKIB1454ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст