Nissan X-Trail 32. Instruction — part 692
4WD CONTROL UNIT
DLN-179
< REMOVAL AND INSTALLATION >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
4WD CONTROL UNIT
Exploded View
INFOID:0000000011004046
Removal and Installation
INFOID:0000000011004047
REMOVAL
1.
Turn the ignition switch OFF.
2.
Remove luggage side lower finisher LH. Refer to
INT-43, "LUGGAGE SIDE LOWER FINISHER :
.
3.
Disconnect 4WD control unit harness connector.
4.
Remove 4WD control unit mounting nuts
and remove 4WD
control unit
.
NOTE:
4WD control unit is located on the back side of the rear wheel
house outer panel LH.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform adjustment after installation. Refer to
.
Adjustment
INFOID:0000000011004048
ADJUSTMENT AFTER INSTALLATION
When replaced 4WD control unit, perform writing unit characteristics. Refer to
4WD control unit
: Vehicle front
: N·m (kg-m, in-lb)
JSDIA5368GB
: Vehicle front
AWDIA1154ZZ
DLN-180
< REMOVAL AND INSTALLATION >
[TRANSFER: TY30A]
4WD MODE SWITCH
4WD MODE SWITCH
Exploded View
INFOID:0000000011004049
Removal and Installation
INFOID:0000000011004050
REMOVAL
1.
Remove console switch panel from center console assembly. Refer to
IP-25, "Removal and Installation"
(LHD models),
IP-52, "Removal and Installation"
(RHD models).
2.
Disconnect 4WD mode switch harness connector.
3.
Remove 4WD mode switch from console switch panel.
INSTALLATION
Install in the reverse order of removal.
4WD mode switch
Console switch panel
JSDIA5457ZZ
TRANSFER ASSEMBLY
DLN-181
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT REMOVAL AND INSTALLATION
TRANSFER ASSEMBLY
Exploded View
INFOID:0000000011004055
Removal and Installation
INFOID:0000000011004056
REMOVAL
1.
Remove engine assembly together with transaxle assembly and transfer assembly from vehicle. Refer to
EM-366, "Removal and Installation"
.
2.
Remove transfer gusset
.
3.
Remove transaxle assembly together with transfer assembly
from engine assembly. Refer to
TM-122, "Removal and Installa-
Transfer gusset
Transfer assembly
O-ring
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
*: Apply anti-corrosion oil.
:Apply multi purpose grease.
JSDIA6409GB
JSDIA6418ZZ
DLN-182
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TY30A]
TRANSFER ASSEMBLY
4.
Remove transfer assembly from transaxle assembly.
CAUTION:
• Be careful not to remove wrong fixing bolts (
). Never
remove the mounting bolts of adapter case.
• Never damage ring gear shaft.
• Never damage air breather hose.
• Never damage oil seal.
5.
Remove O-ring
from transfer assembly.
CAUTION:
• Never use a tool.
• Never damage adapter case.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Apply multi-purpose grease lightly and evenly onto an O-ring, and install it to transfer assembly.
CAUTION:
• Never reuse O-ring.
• When installing O-ring, never use a tool.
• Never damage adapter case and O-ring.
• When installing the transfer to the transaxle, install the mounting
bolts following the standard below, tighten bolts to the specified
torque. For each tightening torque, refer to
.
CAUTION:
Apply anti-corrosion oil to the thread and seat of mounting bolts.
• For mounting bolts of transfer gusset
, temporarily tightening
them first. After this, tighten bolts to the specified torque in the
order from engine side bolts
to transfer side bolts
. For tight-
ening torque, refer to
.
• Perform inspection after installation. Refer to
SDIA3225J
JSDIA6419ZZ
Bolt symbol
Quantity
4
1
Bolt length
“L” mm (in)
55 (2.17)
55 (2.17)
Insertion direction
Transfer to transaxle
Transaxle to transfer
Bolt symbol
Quantity
2
2
Bolt length
“L” mm (in)
35 (1.38)
45 (1.77)
Mounting position
Engine cylinder block side
Transfer side
JSDIA6410ZZ
JSDIA6411ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст