Nissan X-Trail 32. Instruction — part 2219
TPMS
WT-49
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
Low tire pres-
sure warning
lamp
The low tire pres-
sure warning lamp
repeats blinking at
0.5-second inter-
vals for 1 minute,
and then stays illu-
minated.
The BCM cannot detect
tire pressure data signal.
• Check visually that the
tire pressure sensors are
installed. If necessary, re-
place/install the tire pres-
sure sensor(s) and
perform tire pressure
sensor ID registration.
Refer to
• Remove the interference
radio wave (e.g. battery
charger of smart phone).
The combination meter
fuse is open or removed
(or pulled out).
Check and install the com-
bination meter fuse. If nec-
essary, replace the fuse.
The BCM harness con-
nector is removed.
Check the connection con-
ditions of the BCM harness
connector, and repair if nec-
essary.
Tire Pressure Monitoring
System (TPMS) mal-
function.
(except tire pressure
monitoring system con-
figuration and/or tire
pressure sensor ID reg-
istration non-performed)
Perform CONSULT self-di-
agnosis. Refer to
Hazard warning
lamp
The hazard warn-
ing lamp does not
blink twice when
performing ID reg-
istration operation.
—
ID registration is not
completed.
Perform “TIRE PRESSURE
SENSOR ID REGISTRA-
TION CANNOT BE COM-
PLETED” diagnosis
procedure. Refer to
.
Diagnosis items
Symptom
(Ignition switch
ON)
Low tire pressure warning lamp
Cause
Action
SEIA0788E
WT-50
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000010715103
The low tire pressure warning lamp does not turn ON when the ignition switch is turned ON.
NOTE:
The low tire pressure warning lamp turn ON for approximately 1 second and then turns OFF when the ignition
switch is turned ON. This is to check that no abnormal condition is present in the tire pressure monitoring sys-
tem.
The combination meter may be malfunctioning or the tire pressure monitoring system may be malfunctioning if
the low tire pressure warning lamp does not turn ON when the ignition switch is turned ON.
Diagnosis Procedure
INFOID:0000000010715104
1.
CHECK LOW TIRE PRESSURE WARNING LAMP SIGNAL
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Select “ACTIVE TEST” in “AIR PRESSURE MONITOR”.
3.
Touch “WARNING LAMP” to turn ON the low tire pressure warning lamp.
When “ACTIVE TEST” is performed, does the low tire pressure warning lamp in the combination meter turn
ON?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK LOW TIRE PRESSURE WARNING LAMP OPERATION
Check that the low tire pressure warning lamp is turned OFF after turns ON for approximately 1 second, when
the ignition switch is turned ON.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
BCS-121, "Removal and Installation"
3.
CHECK COMBINATION METER POWER SUPPLY CIRCUIT
Perform the trouble diagnosis for combination meter power supply circuit. Refer to
Is the inspection result normal?
YES
>> Perform combination diagnosis. Refer to
NO
>> Repair or replace error-detected parts.
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
WT-51
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000010715105
The low tire pressure warning lamp does not turn OFF after several seconds is passed after engine starts.
Diagnosis Procedure
INFOID:0000000010715106
1.
CHECK TIRE PRESSURE
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
3.
Perform TPMS reset operation. Refer to
4.
Recheck the tire pressure for all wheels. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels.
2.
CHECK LOW TIRE PRESSURE WARNING LAMP OPERATION
Check that the low tire pressure warning lamp is turned OFF after turns ON for approximately 1 second, when
the ignition switch is turned ON.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 3.
3.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC detected?
YES
>> Perform DTC diagnosis procedure. Refer to
NO
>> GO TO 4.
4.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for power supply and ground circuit. Refer to
BCS-114, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
NO
>> Repair or replace error-detected parts.
WT-52
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP BLINKS
LOW TIRE PRESSURE WARNING LAMP BLINKS
Description
INFOID:0000000010715107
When the ignition switch is turned ON, the low tire pressure warning lamp blinks. And then 1 minute later, low
tire pressure warning lamp turns ON.
Diagnosis Procedure
INFOID:0000000010715108
1.
CHECK TIRE PRESSURE SENSOR INSTALLATION
Check visually that tire pressure sensors are installed to each wheels correctly.
NOTE:
In the following case, tire pressure monitoring system (TPMS) does not function.
• Tire pressure sensor(s) are not installed.
• Tire pressure sensor(s) of other cars are installed.
Are the genuine NISSAN tire pressure sensors are installed correctly?
YES
>> GO TO 2.
NO
>> Replace and/or Install tire pressure sensor(s). Refer to
WT-62, "Removal and Installation"
. GO TO
3.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC detected?
YES
>> Perform DTC diagnosis procedure. Refer to
NO
>> GO TO 4.
3.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Is tire pressure sensor ID registration completed?
YES
>> Adjust the tire pressure for all wheels specified to the value. Refer to
.
And perform TPMS reset operation. Refer to
. INSPECTION END
NO
>> Perform diagnosis procedure of “TIRE PRESSURE SENSOR ID REGISTRATION CANNOT BE
4.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for power supply and ground circuit. Refer to
BCS-114, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
NO
>> Repair or replace error-detected parts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст