Nissan X-Trail 32. Instruction — part 1551
LU-40
< PERIODIC MAINTENANCE >
[R9M]
OIL FILTER
OIL FILTER
Removal and Installation
INFOID:0000000010783326
REMOVAL
WARNING:
Be careful not to get burned when engine and engine oil may be hot.
CAUTION:
• When removing, prepare a shop cloth to absorb any engine oil leakage or spillage.
• Completely wipe off any engine oil that adheres to engine and vehicle.
1.
Remove engine under cover. Refer to
EXT-39, "ENGINE UNDER COVER : Exploded View"
2.
Loosen oil filter body
using a socket [27 mm (1.06 in)].
• Loosen oil filter body until orifice
of the oil filter body is
exposed, and then drain engine oil.
• Catch the engine oil drip, using a tray or waste.
CAUTION:
Completely wipe clean any engine oil remaining on oil fil-
ter body or vehicle.
3.
Remove oil filter body
, and then remove oil filter
and O-ring
.
• Push the O-ring in the one direction by hand, and then pick a
pushed out-part with fingers to remove the O-ring.
CAUTION:
Never use wires or screwdrivers to prevent the oil filter
body from damage.
INSTALLATION
1.
Completely remove all foreign objects adhering to the inside of oil filter body or O-ring mounting area.
E1BIA0602ZZ
: Oil cooler side
E1BIA0600ZZ
OIL FILTER
LU-41
< PERIODIC MAINTENANCE >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
2.
Install oil filter
and O-ring
to oil filter body
.
CAUTION:
Be sure to use a new O-ring.
• Securely press the oil filter into the oil filter body.
• When installing an O-ring, apply engine oil all around the O-
ring.
3.
Install oil filter body assembly to oil cooler. Refer to
Inspection
INFOID:0000000010783327
INSPECTION AFTER INSTALLATION
1.
Check that the engine oil level. Refer to
2.
Start the engine, and check that there is no leak of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check that the engine oil level, and adjust the level. Refer to
: Oil cooler side
E1BIA0600ZZ
LU-42
< REMOVAL AND INSTALLATION >
[R9M]
OIL COOLER
REMOVAL AND INSTALLATION
OIL COOLER
Exploded View
INFOID:0000000010783328
Removal and Installation
INFOID:0000000010783329
REMOVAL
WARNING:
Be careful not to get burn yourself, as engine oil and engine coolant may be hot.
1.
Drain engine coolant from radiator. Refer to
.
CAUTION:
Perform this step when the engine is cold.
2.
Disconnect air inlet tube 2 (charge air cooler side). Refer to
Oil cooler bolt
Oil cooler
Gasket
Oil pressure sensor
Oil filter
O-ring
Oil filter body
Water hose
.
Comply with the installation proce-
dure when tightening. Refer to
To thermoplunger
To water inlet
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JPBIA6961GB
OIL COOLER
LU-43
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
3.
Remove A/C compressor from bracket with piping connected, and temporarily secure it aside. Refer to
(for RUSSIA) or
(except for RUSSIA).
4.
Disconnect oil level sensor and oil pressure switch harness connectors.
5.
Disconnect water hose from oil cooler. (To water inlet)
CAUTION:
Never adhere the engine coolant to electronic equipments. (alternator etc.)
6.
Remove oil pressure switch, if necessary.
CAUTION:
Handle oil pressure switch carefully and avoid impacts.
7.
Remove oil cooler.
• Loosen mounting bolts in reverse order as shown in the figure.
8.
Disconnect water hose from oil cooler. (To thermoplunger)
INSTALLATION
Note the following, and install in the reverse order of removal.
Oil Cooler
• Tighten mounting bolts in the following steps in numerical order as
shown in the figure.
1.
Tighten mounting bolts No.1 and 6.
2.
Tighten all mounting bolts.
Inspection
INFOID:0000000010783330
INSPECTION AFTER REMOVAL
Oil Cooler
Check that oil cooler for cracks. Check that oil cooler for clogging by blowing through engine coolant inlet. If
necessary, replace oil cooler.
INSPECTION AFTER INSTALLATION
1.
Check that the engine oil level and the engine coolant level and add engine oil and engine coolant. Refer
to
.
2.
Start the engine, and check that there is no leakage of engine oil or engine coolant.
3.
Stop the engine and wait for 10 minutes.
4.
Check that the engine oil level and the engine coolant level again. Refer to
E1BIA0599ZZ
: 10.0 N·m (1.0 kg-m, 89 in-lb)
: 10.0 N·m (1.0 kg-m, 89 in-lb)
E1BIA0599ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст