Nissan X-Trail 32. Instruction — part 1114
TIMING SPROCKET
EM-353
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
TIMING SPROCKET
Exploded View
INFOID:0000000011006364
Front cover
Exhaust camshaft timing sprocket
bolt
Guide bolt
Timing sprocket spacer
Exhaust camshaft timing sprocket
(front)
Exhaust camshaft timing sprocket
(rear)
Exhaust camshaft
Intake camshaft
Intake camshaft timing sprocket
Intake camshaft timing sprocket
spacer
Intake camshaft timing sprocket bolt
Crankshaft
Tension guide
Crankshaft sprocket
Timing chain
Slack guide
Timing chain tensioner
Crankshaft spacer
Timing chain cover pin
Front oil seal
Crankshaft pulley bolt
Crankshaft spacer
Crankshaft pulley
JPBIA6954GB
EM-354
< REMOVAL AND INSTALLATION >
[R9M]
TIMING SPROCKET
Removal and installation
INFOID:0000000010784347
REMOVAL
1.
Remove the timing chain. Refer to
.
2.
Immobilize the intake camshaft timing sprocket using the tool
[SST: — (Mot.1969)]
3.
Loosen the intake camshaft timing sprocket bolt
.
4.
Remove the tool [SST: — (Mot.1969)].
5.
Place a screw driver in the hole
, compress the spring of the
intake camshaft timing sprocket
and remove the exhaust
camshaft timing sprocket (rear)
.
6.
Remove the intake camshaft timing sprocket with the following procedure:
a.
Remove the screwdriver.
b.
Remove the intake camshaft timing sprocket bolt.
c.
Remove the intake camshaft timing sprocket spacer.
d.
Remove the intake camshaft timing sprocket.
INSTALLATION
1.
Install the intake camshaft timing sprocket with the following procedure:
Comply with the installation proce-
dure when tightening. Refer to
347, "Removal and Installation"
.
Comply with the installation proce-
dure when tightening. Refer to
354, "Removal and installation"
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Should be lubricated with oil.
: Sealing point
: Indicates that the part is connected at points with same symbol in actual vehicle.
E1BIA0455ZZ
E1BIA0456ZZ
TIMING SPROCKET
EM-355
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
a.
Set the intake camshaft timing sprocket
on base plate of posi-
tioning tool [SST: — (Mot. 1773)] (A).
b.
Set the lever (B) in the lower gear teeth
. Pivot the lever coun-
terclockwise until the two gear teeth are aligned.
c.
Set a stopper pin (A) in the gear hole.
NOTE:
• Use approximately 4.0 mm (0.157 in) dia. hard metal pin as a
stopper pin
d.
Install intake camshaft timing sprocket
and intake camshaft
timing sprocket spacer
to the camshaft.
e.
Align matching mark
on intake camshaft timing sprocket and
mark
of cylinder head housing.
f.
Temporarily tighten mounting bolt.
2.
Install exhaust camshaft timing sprocket (rear) with the following procedure:
a.
Check that the exhaust camshaft groove
is horizontal (large ring facing upwards).
JPBIA0766ZZ
: Wear compensation gear
JPBIA0594ZZ
: Wear compensation gear
JPBIA0595ZZ
C : Stopper pin
JPBIA0616ZZ
EM-356
< REMOVAL AND INSTALLATION >
[R9M]
TIMING SPROCKET
b.
Center the exhaust camshaft timing sprocket (rear) openings on
the camshaft hub mounting holes
.
c.
Set the exhaust camshaft timing sprocket (rear) fully onto the
camshaft (right side) hub.
d.
Remove stopper pin.
3.
Re-install the tool [SST: — (Mot.1969)] to immobilize the intake camshaft timing sprocket.
4.
Tighten the intake camshaft timing sprocket bolt
5.
Turn 35 degrees clockwise (angle tightening).
6.
Install in the reverse order of removal.
E1BIA0462ZZ
Intake camshaft timing
sprocket bolt:
20 N·m (2.0 kg-m, 15 ft-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст