Nissan X-Trail 32. Instruction — part 540
HANDS FREE SENSOR
DLK-501
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK HANDS FREE SENSOR OUTPUT SIGNAL
1.
Disconnect hands free sensor connector.
2.
Check voltage between hands free sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> GO TO 8.
8.
CHECK HANDS FREE SENSOR CANCEL SIGNAL CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and hands free sensor harness connector.
3.
Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
NO
>> Repair or replace harness.
9.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Automatic back door main switch
Ground
Continuity
Connector
Terminal
M54
3
Existed
(+)
(–)
Voltage
Hands free sensor
Connector
Terminal
D170
2
Ground
9 – 16 V
BCM
Hands free sensor
Continuity
Connector
Terminal
Connector
Terminal
B47
9
D170
2
Existed
Automatic back door main switch
Ground
Continuity
Connector
Terminal
B47
9
Not existed
DLK-502
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
HAZARD FUNCTION
HAZARD FUNCTION
Component Function Check
INFOID:0000000010717563
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “FLASHER” in “ACTIVE TEST” mode.
3.
Touch “LH” or “RH” to check that it works normally.
Is the inspection result normal?
YES
>> Hazard warning lamp circuit is OK.
NO
>> Refer to
DLK-502, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010717564
1.
CHECK HAZARD OPERATION
EXL-36, "TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Description"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
INFORMATION DISPLAY
DLK-503
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INFORMATION DISPLAY
Component Function Check
INFOID:0000000010717565
1.
CHECK FUNCTION
1.
Turn ignition switch ON.
2.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
3.
Select “INDICATOR” in “ACTIVE TEST” mode.
4.
Touch “KEY ON” or “KEY IND” to check that it works normally.
Is the inspection result normal?
YES
>> Information display is OK.
NO
>> Refer to
DLK-503, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010717566
1.
CHECK COMBINATION METER
MWI-84, "On Board Diagnosis Function"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
DLK-504
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
INTELLIGENT KEY BATTERY
INTELLIGENT KEY BATTERY
Component Inspection
INFOID:0000000010717567
1.
CHECK INTELLIGENT KEY BATTERY
Check by connecting a resistance (approximately 300
Ω
) so that the
current value becomes about 10 mA. Refer to
.
Is the measurement value within the specification?
YES
>> INSPECTION END
NO
>> Replace Intelligent Key battery.
Standard
: Approx. 2.5 - 3.0 V
OCC0607D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст