Nissan X-Trail 32. Instruction — part 1799
SE-44
< REMOVAL AND INSTALLATION >
FRONT SEAT
7.
Disengage seatback trim fixing retainer
, heater seat harness
connector
and seat heater harness clip.
8.
Remove headrest holder by raising it while pinching the pawls
from the bottom of the headrest holder.
CAUTION:
Before installing headrest holder, check its orientation
(front/rear and right/left).
9.
Remove seatback trim and seatback pad as a set.
10. Remove seatback silencer.
11. Remove lumber support harness connector
.
: Clip
JMJIA9578ZZ
JMJIA9579ZZ
JMJIA9580ZZ
JMJIB0141ZZ
FRONT SEAT
SE-45
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
12. Remove seatback suspension
.
13. Remove hog rings, and then separate seatback pad and seatback trim.
CAUTION:
• Never disassembly / separate front seat with heated seat.
• Before performing separating operation, check the installation position of hog rings.
14. Remove seatback frame.
a.
Disconnect harness connector
and disengage harness clip
(power seat).
b.
Remove seat cushion outside finisher. Refer to
SE-48, "SEAT CUSHION FINISHER : Disassembly and
c.
Disengage harness clip
, remove seatback frame fixing bolts
, and then remove seatback frame.
ASSEMBLY
Note the following items, and then assemble in the reverse order of disassembly.
CAUTION:
• For hog ring that is removed or crimped unsuccessfully, fix it by using a new hog ring. (Never reuse
hog ring.)
• Always install the hog rings in position.
• When installing the side air bag, check that the inner cloth (reinforcement cloth) is not caught in bolt
hole.
• Note the following for side air bag module fixing nuts.
- Always use new fixing nuts (prevents the nut from loosening).
- Never tighten nuts twice (prevents improper torque).
• Note the following for seatback frame fixing bolts.
JMJIA9581ZZ
: Clip
JMJIB0142ZZ
: Clip
JMJIA9597ZZ
SE-46
< REMOVAL AND INSTALLATION >
FRONT SEAT
- Starting from vehicle rear, outside, temporarily tighten bolts in
order (1
→
4 as shown in the figure) and then perform final
tightening in the same order.
- After tightening, never use bolts that are loosened or removed. (This is because bolts applied with a
lock coating agent are used.)
SEAT CUSHION
SEAT CUSHION : Disassembly and Assembly
INFOID:0000000010713135
DISASSEMBLY
CAUTION:
• Never separate the passenger seat cushion trim and passenger seat cushion pad for with occupant
sensor.
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
1.
Remove seat cushion outside finisher outer side. Refer to
SE-48, "SEAT CUSHION FINISHER : Disas-
.
2.
Disengage harness fixing magic fasteners
.
3.
Disengage seatback trim fixing retainers
.
JMJIA9598ZZ
JMJIA9582ZZ
JMJIA9572ZZ
FRONT SEAT
SE-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
4.
Disengage seat cushion trim fixing retainers
, and disconnect seat heater harness connector
.
5.
Disconnect occupant sensor harness connector
and disan-
gage harness clip (if equipped).
6.
Remove seat cushion trim and seat cushion pad as a set.
7.
Remove seat cushion silencer.
8.
Disengage harness connector, harness clips, and then remove
seat cushion suspension
.
9.
Remove hog rings, and then separate the seat cushion trim and seat cushion pad.
CAUTION:
• Never separate the passenger seat with occupant sensor.
• Never separate the front seat with heater seat.
• Before performing separating operation, check the installation position of hog rings.
ASSEMBLY
Note the following items, and then assemble in the reverse order of disassembly.
CAUTION:
• For hog ring that is removed or crimped unsuccessfully, fix it by using a new hog ring. (Never reuse
hog ring.)
• Always install the hog rings in position.
JMJIA9583ZZ
: Clip
JMJIB0143ZZ
JMJIA9584ZZ
: Clip
JMJIA9585ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст