Nissan X-Trail 32. Instruction — part 350
DAS
DRIVER ASSISTANCE SYSTEM SYMPTOMS
DAS-141
< SYMPTOM DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
*: Check if the road sign can be displayed with TSR. Refer to
DAS-21, "TSR : System Description"
DAA is not functioning normally
A warning is issued even when the driver is in normal condition
Remove the around view moni-
tor control unit
Refer to
.
DAA warning display does not il-
luminate
Information display is functioning normally
Remove the around view moni-
tor control unit
Refer to
.
Information display is not functioning normally
On board diagnosis function
(Combination meter)
Refer to
TSR is not functioning normally
• A road sign different from actual one is displayed or no road
sign is displayed
• A road sign is displayed despite no road sign
Remove the front camera unit
Refer to
TSR display does not illuminate
*
Information display is functioning normally
Remove the front camera unit
Refer to
Information display is not functioning normally
On board diagnosis function
(Combination meter)
Refer to
Symptom
Confirmation item
Inspection item/Reference page
DAS-142
< SYMPTOM DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
SYSTEM SETTINGS CANNOT BE TURNED ON/OFF
SYSTEM SETTINGS CANNOT BE TURNED ON/OFF
Description
INFOID:0000000010727949
System setting is not selectable on the combination meter.
• Lane Departure Warning (LDW)
• Blind Spot Warning (BSW)
• Traffic Sign Recognition (TSR)
• Driver Attention Alert (DAA)
NOTE:
When the ignition switch is in ACC position, each system settings cannot be changed.
Diagnosis Procedure
INFOID:0000000010727950
1.
CHECK SYSTEM SETTING
1.
Start the engine.
2.
Check that the each system settings is selectable on the combination meter.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1 (LDW/TSR)>>GO TO 3.
NO-1 (BSW/DAA)>>GO TO 4.
2.
PERFORM THE SELF-DIAGNOSIS
1.
Perform “All DTC Reading” with CONSULT.
2.
Check if the DTC is detected in self-diagnosis results of “LANE CAMERA”, “AVM” and “METER/M&A”.
Refer to the following.
-
LAME CAMERA:
-
AVM:
-
METER/M&A:
Is any DTC detected?
YES
>> Repair or replace malfunctioning parts.
NO
>> INSPECTION END
3.
CHECK DATA MONITOR OF FRONT CAMERA UNIT
Check that “LDW STATUS DISPLAY” or “TSR STATUS” operates normally in “DATA MONITOR” of “LANE
CAMERA” with CONSULT.
Is the inspection result normal?
YES
>> Refer to
MWI-84, "On Board Diagnosis Function"
.
NO
>> GO TO 4.
4.
CHECK STERING SWITCH
Operate the steering switch to check that the information display on the combination meter operate properly.
Is the inspection result normal?
YES-1 (LDW/TSR)>>Replace the front camera unit. Refer to
DAS-149, "Removal and Installation"
.
YES-2 (BSW/DAA)>>Replace the around view monitor control unit. Refer to
AV-268, "Removal and Installa-
].
NO
>> Repair or replace malfunctioning parts.
DAS
CHIME DOES NOT SOUND
DAS-143
< SYMPTOM DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
CHIME DOES NOT SOUND
Description
INFOID:0000000010727951
The warning chime does not sound when the system is warning to driver.
Diagnosis Procedure
INFOID:0000000010727952
1.
CHECK THE VEHICLE SPECIFICATION
Check the vehicle specification.
With sonar system>>GO TO 2.
Without sonar system>>GO TO 3.
2.
PERFORM ACTIVE TEST
Check if the warning chime sounds on the active test item “FRONT BUZZER” of “SONAR” with CONSULT.
Does the warning chime sound?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK OPERATION OF METER BUZZER
Check operation of meter buzzer. Refer to
WCS-54, "Component Function Check"
Is the inspection result normal?
YES
>> Repair or replace malfunctioning parts.
NO
>> GO TO 4.
4.
CHECK THE MALFUNCTION SYMPTOM DURING WARNING CHIME OPERATION
Understand the vehicle ahead detection condition when the malfunction occurred. If the warning chime should
have sounded, replace the front camera unit or the around view monitor control unit. Refer to following.
• LDW:
DAS-30, "LDW : Menu Displayed by Pressing Each Switch"
DAS-33, "BSW : Menu Displayed by Pressing Each Switch"
• DAA:
DAS-38, "DAA : Menu Displayed by Pressing Each Switch"
Does the warning chime sound?
YES
>> INSPECTION END
NO (LDW does not sound.)>>GO TO 5.
NO (BSW or DAA does not sound.)>>GO TO 6.
5.
PERFORM THE SELF-DIAGNOSIS
1.
Perform “All DTC Reading” with CONSULT.
2.
Check if the “U1000” is detected in self-diagnosis results of “LANE CAMERA”.
Is “U1000” detected?
YES
>> Check the CAN communication and repair or replace malfunctioning parts. Refer to
NO
>> GO TO 7.
6.
PERFORM THE SELF-DIAGNOSIS
1.
Perform “All DTC Reading” with CONSULT.
2.
Check if the “U1000” is detected in self-diagnosis results of “AVM”.
Is “U1000” detected?
YES
>> Check the CAN communication and repair or replace malfunctioning parts. Refer to
"AROUND VIEW MONITOR CONTROL UNIT : DTC Description"
.
NO
>> GO TO 8.
7.
REPLACE FRONT CAMERA UNIT
Replace the front camera unit. Refer to
DAS-149, "Removal and Installation"
.
>> GO TO 9.
DAS-144
< SYMPTOM DIAGNOSIS >
[DRIVER ASSISTANCE SYSTEM]
CHIME DOES NOT SOUND
8.
REPLACE AROUND VIEW MONITOR CONTROL UNIT
Replace the around view monitor control unit. Refer to
AV-268, "Removal and Installation"
>> GO TO 9.
9.
CHECK IF THE EACH SYSTEM IS NORMAL.
1.
Erase “self-diagnosis result”, and then perform “All DTC Reading” again after performing the action
test.Refer to the following.
-
Lane Departure Warning (LDW):
DAS-91, "LDW : Work Procedure"
-
Blind Spot Warning (BSW):
DAS-92, "BSW : Work Procedure"
-
Driver Attention Alert (DAA):
DAS-95, "DAA : Work Procedure"
2.
Check if the each system is normal.
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст