Nissan X-Trail 32. Instruction — part 2250
HEADLAMP WASHER
WW-107
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Check that washer fluid is sprayed on the luminescent surface of lamp.
WASHER TUBE
WASHER TUBE : Removal and Installation
INFOID:0000000010786693
REMOVAL
1.
Remove front bumper fascia. Refer to
EXT-15, "Removal and Installation"
.
2.
Disconnect headlamp washer tube connector
, and then remove headlamp washer tube from headlamp
washer nozzle.
NOTE:
• Move headlamp washer tube connector
toward the direction of arrow (1) to unlock.
• Move headlamp washer tube connector
toward the direction of arrow (2) to lock.
3.
Disengage headlamp washer tube fixing tube clips, and then remove headlamp washer tube.
INSTALLATION
Note the following item, and then Install in the reverse order of removal.
CAUTION:
Add washer liquid up to the top of the washer tank inlet after installing. Check that there is no leakage.
WASHER PUMP
WASHER PUMP : Removal and Installation
INFOID:0000000010786694
REMOVAL
CAUTION:
When the headlamp washer tube and headlamp washer tube is removed, washer fluid may come out
so prepare a container to receive the fluid and never allow fluid to be sprinkled.
1.
Remove front fender protector RH. Refer to
EXT-35, "FENDER PROTECTOR : Removal and Installation"
.
LED headlamp
Halogen headlamp
: Shooting area
: Lamp light-emitting area
JMLIA5417ZZ
JMLIA5414ZZ
WW-108
< REMOVAL AND INSTALLATION >
HEADLAMP WASHER
2.
Disconnect headlamp washer tube connector
, and then remove headlamp washer tube from washer
tank.
NOTE:
• Move headlamp washer tube connector
toward the direction of arrow (1) to unlock.
• Move headlamp washer tube connector
toward the direction of arrow (2) to lock.
3.
Disconnect headlamp washer pump harness connector.
4.
Pull out headlamp washer pump from washer tank.
5.
Remove packing.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Check that packing is inserted fully. (This may be the cause of washer fluid leakage and washer
pump looseness.)
• Add washer liquid up to the top of the washer tank inlet after installing. Check that there is no leak-
age.
: Vehicle front
JMLIA5418ZZ
: Vehicle front
JMLIA5419ZZ
LIGHT & RAIN SENSOR
WW-109
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
LIGHT & RAIN SENSOR
Exploded View
INFOID:0000000010785471
WITH FRONT CAMERA UNIT
.
WITHOUT FRONT CAMERA UNIT
Removal and Installation
INFOID:0000000010785472
REMOVAL
With Front Camera Unit
1.
Remove front camera unit cover. Refer to
DAS-149, "Removal and Installation"
2.
Disconnect rain sensor harness connector.
3.
Disengage rain sensor fixing lock spring portion
, and then
Peel off rain sensor.
Rain sensor bracket
Rain sensor cover
Rain sensor
Lock spring
: Pawl
: Always replace after every disassembly.
JMLIA1686ZZ
JMLIA4203ZZ
WW-110
< REMOVAL AND INSTALLATION >
LIGHT & RAIN SENSOR
Without Front Camera Unit
1.
Disengage rain sensor cover fixing pawls, and then remove rain sensor cover.
2.
Disconnect rain sensor harness connector.
3.
Disengage rain sensor fixing lock spring portion
, and then
Peel off rain sensor.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace rain sensor with a new part after removal. Never reuse rain sensor.
• Clean the sensor installation portion of the windshield.
• When the sensor is removed, wipe off the silicon pad remaining on the windshield surface.
• Remove the sensor protective cover just before installation.
• Never touch the silicon pad
after removal of sensor protec-
tive cover.
• Install the rain sensor so that the connector faces vehicle upward.
• When installing, never allow silicon pad to touch the sensor bracket and other parts.
• Compress the lock spring portion
vertically to the glass
surface and fully engage both ends of lock spring.
• Never use a sensor that is dropped.
• Perform check after replacement. Refer to
.
Inspection
INFOID:0000000010785473
CAUTION:
Clean the windshield glass and wiper refill so that the windshield glass may not be damaged by dust,
etc.
1.
Push the ignition switch to the ON position, and set the combination switch to AUTO.
JMLIA4203ZZ
JMLIA4204ZZ
JMLIA4205ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст