Nissan X-Trail 32. Instruction — part 983
P0560 BATTERY VOLTAGE
EC-1061
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
NO
>> Recharge the battery.
2.
CHECK BATTERY TERMINALS
1.
Turn ignition switch OFF.
2.
Check battery terminals condition.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the battery terminals.
3.
CHECK BATTERY AND ALTERNATOR
Check that the proper type of battery and type of alternator are installed.
Refer to,
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace with a proper one.
EC-1062
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0564 ASCD STEERING SWITCH
P0564 ASCD STEERING SWITCH
DTC Description
INFOID:0000000010935744
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors (The switch circuit is open or shorted.)
• ASCD steering switch
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 10 seconds.
2.
Press RESUME/ACCELERATE switch for at least 10 seconds, then release it and wait at least 10 sec-
onds.
3.
Press SET/COAST switch for at least 10 seconds, then release it and wait at least 10 seconds.
4.
Press CANCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.
5.
Check DTC.
Is DTC detected?
YES
>> Proceed to
EC-1062, "Diagnosis Procedure"
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010935745
1.
CHECK ASCD STEERING SWITCH CIRCUIT
1.
Turn ignition switch ON.
2.
Check the voltage between ECM harness connector terminals as follows.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P0564
SL LMTR/CC FNC
(Cruise control multi-function input “A” cir-
cuit)
• 1.DEF: VALUES OUTSIDE TOLERANC-
ES
• 2.DEF: SIGNAL INCOHERENCE
• CO.1: OPEN CIRCUIT OR SHORT CIR-
CUIT TO +12 V
• An ASCD steering switch signal voltage is out of the specified range.
• ASCD steering switch signal circuit is open.
• ASCD steering switch signal circuit is short to battery.
• ECM cannot detect the ASCD steering switch signal.
ECM
Condition
Voltage
(Approx.)
Connector
+
–
Terminal
E79
18
19
CANCEL switch: Pressed
1.0 V
SET/COAST switch: Pressed
2.0 V
RESUME/ACCELERATE switch: Pressed
3.0 V
All ASCD steering switches: Released
4.0 V
P0564 ASCD STEERING SWITCH
EC-1063
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK ASCD STEERING SWITCH GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF and wait at least 1 minute.
2.
Disconnect combination switch harness connector.
3.
Disconnect ECM harness connector.
4.
Check the continuity between combination switch (spiral cable) and ECM harness connector.
5.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
3.
CHECK ASCD STEERING SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check the continuity between combination switch (spiral cable) and ECM harness connector.
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
4.
CHECK ASCD STEERING SWITCH
EC-1063, "Component Inspection (ASCD Steering Switch)"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace ASCD steering switch.
Component Inspection (ASCD Steering Switch)
INFOID:0000000010935746
1.
CHECK ASCD STEERING SWITCH
1.
Disconnect combination switch (spiral cable) harness connector.
2.
Check the continuity between combination switch harness connector terminals under following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
+
-
Continuity
Combination switch (spiral cable)
ECM
Connector
Terminal
Connector
Terminal
M33
28
E79
19
Existed
+
-
Continuity
Combination switch (spiral cable)
ECM
Connector
Terminal
Connector
Terminal
M33
27
E79
18
Existed
Combination switch
Condition
Resistance
(Approx.)
Connector
+
-
Terminals
M303
8
9
CANCEL switch: Pressed
250
Ω
SET/COAST switch: Pressed
660
Ω
RESUME/ACCELERATE switch: Pressed
1,480
Ω
All ASCD steering switches: Released
4,000
Ω
EC-1064
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0564 ASCD STEERING SWITCH
NO
>> Replace ASCD steering switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст