Nissan X-Trail 32. Instruction — part 1910
SN-96
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT PARK ASSIST]
B272C-14 CORNER SENSOR [FR]
B272C-14 CORNER SENSOR [FR]
DTC Description
INFOID:0000000010735596
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors (corner sensor front RH circuit)
• Corner sensor front RH
FAIL-SAFE
• Obstacle detection function is stopped
• Alarm display is displayed on the information display of combination meter
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.
5.
Check DTC.
Is DTC B272C-14 detected?
YES
>> Proceed to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010735597
1.
CHECK CORNER SENSOR SIGNAL FRONT RH CIRCUIT FOR OPEN
1.
Turn ignition switch OFF.
2.
Disconnect sonar control unit harness connector and corner sensor front RH harness connector.
3.
Check the continuity between sonar control unit harness connector and corner sensor front RH harness
connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK CORNER SENSOR SIGNAL FRONT RH CIRCUIT FOR SHORT
Check the continuity between sonar control unit harness connector and ground.
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
B272C-14
CORNER SENSOR [FR]
(Corner sensor front-right)
OPEN/SHORT-
GND
(Open/Short to
ground)
Short circuit to ground or open circuit is detected in harness be-
tween sonar control unit and corner sensor front RH when ignition
switch is turned ON.
Sonar control unit
Corner sensor front RH
Continuity
Connector
Terminal
Connector
Terminal
B101
4
E134
2
Existed
SN
B272C-14 CORNER SENSOR [FR]
SN-97
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT PARK ASSIST]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK FRONT SENSOR GROUND CIRCUIT
Check the continuity between sonar control unit harness connector and corner sensor front RH harness con-
nector.
Is the inspection result normal?
YES
>> Replace corner sensor front RH. Refer to
SN-113, "FRONT : Removal and Installation"
NO
>> Repair or replace malfunctioning parts.
Terminals
Continuity
(+)
(
−
)
Sonar control unit
Connector
Terminal
B101
4
Ground
Not existed
Sonar control unit
Corner sensor front RH
Continuity
Connector
Terminal
Connector
Terminal
B101
13
E134
1
Existed
SN-98
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT PARK ASSIST]
B272C-55 CORNER SENSOR [FR]
B272C-55 CORNER SENSOR [FR]
DTC Description
INFOID:0000000010735598
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Corner sensor front RH
• Control unit setting of sonar control unit is incomplete
FAIL-SAFE
• Obstacle detection function is stopped
• Alarm display is displayed on the information display of combination meter
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.
5.
Check DTC.
Is DTC B272C-55 detected?
YES
>> Proceed to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010735599
1.
PERFORM CONFIGURATION OF SONAR CONTROL UNIT
Perform configuration of sonar control unit. Refer to
SN-41, "CONFIGURATION (SONAR CONTROL UNIT) :
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Perform DTC confirmation procedure again. Refer to
Is DTC B272C-55 detected again?
YES
>> Replace corner sensor front RH. Refer to
SN-113, "FRONT : Removal and Installation"
NO
>> INSPECTION END.
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
B272C-55
CORNER SENSOR [FR]
(Corner sensor front-right)
CONFIG ERROR
(Configuration er-
ror)
Control unit setting of sonar control unit is incomplete or is not set
normally.
SN
B272C-92 CORNER SENSOR [FR]
SN-99
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT PARK ASSIST]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B272C-92 CORNER SENSOR [FR]
DTC Description
INFOID:0000000010735600
DTC DETECTION LOGIC
POSSIBLE CAUSE
Corner sensor front RH
FAIL-SAFE
• Obstacle detection function is stopped
• Alarm display is displayed on the information display of combination meter
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.
5.
Check DTC.
Is DTC B272C-92 detected?
YES
>> Proceed to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010735601
1.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
With CONSULT
1.
Turn ignition switch ON.
2.
Erase DTC.
3.
Perform DTC confirmation procedure again. Refer to
Is DTC B272C-92 detected again?
YES
>> Replace corner sensor front RH. Refer to
SN-113, "FRONT : Removal and Installation"
NO
>> INSPECTION END
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detecting condition
B272C-92
CORNER SENSOR [FR]
(Corner sensor front-right)
SENSOR
(Sensor)
Corner sensor front RH malfunction is detected when ignition switch
is turned ON.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст