Nissan X-Trail 32. Instruction — part 1750
REAR DRIVE SHAFT
RAX-17
< PERIODIC MAINTENANCE >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
REAR DRIVE SHAFT
Inspection
INFOID:0000000010828166
REAR DRIVE SHAFT INSPECTION
Check the following items, and replace the part if necessary.
• Check drive shaft mounting point and joint for looseness and other damage.
CAUTION:
Replace entire drive shaft assembly when noise or vibration occur from drive shaft.
• Check boot for cracks and other damage.
RAX-18
< REMOVAL AND INSTALLATION >
[4WD]
REAR WHEEL HUB AND HOUSING
REMOVAL AND INSTALLATION
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000010828167
Removal and Installation
INFOID:0000000010828168
REMOVAL
Wheel Hub and Bearing Assembly
1.
Remove tires. Refet to
.
2.
Remove wheel sensor from axle housing. Refer to
BRC-213, "REAR WHEEL SENSOR : Exploded View"
.
3.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work.
• LHD: Refer to
BR-63, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
• RHD: Refer to
BR-123, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
CAUTION:
Never depress brake pedal while brake caliper is removed.
4.
Remove disc rotor. If disc rotor cannot be removed, remove as follows.
CAUTION:
• Parking brake completely in the released position.
Axle housing
Suspension arm
Back plate
Hub bolt
Wheel hub and bearing assembly
Disc rotor
Plug
Wheel hub lock nut
Cotter pin
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JMDIA1517GB
REAR WHEEL HUB AND HOUSING
RAX-19
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
• Put matching marks
on the wheel hub and bearing
assembly and the disc rotor before removing the disc
rotor.
• Never drop disc rotor.
a.
Fix the disc rotor with wheel nuts and remove the adjusting hole
plug.
b.
Using suitable tool, rotate adjuster
in the direction
to retract
and loosen brake shoe.
c.
Remove disc rotor.
5.
Remove cotter pin, and then loosen wheel hub lock nut, using a
wheel hub lock nut wrench (A) (SST: KV40104000).
6.
Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub and bearing assembly from drive
shaft.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive
shaft cannot be separated even after performing the above pro-
cedure.
7.
Remove wheel hub and bearing assembly.
CAUTION:
Remove parking brake assembly only when necessary.
8.
Remove back plate.
9.
If axle housing need to be removed, remove drive shaft. Refer to
RAX-22, "Removal and Installation"
.
JPDIG0066ZZ
JPDIG0204ZZ
PDIA1181J
JPDIG0070ZZ
RAX-20
< REMOVAL AND INSTALLATION >
[4WD]
REAR WHEEL HUB AND HOUSING
10. Remove hub bolts
from wheel hub and bearing assembly,
using the ball joint remover (A) (commercial service tool).
CAUTION:
• Remove hub bolt only when necessary.
• Never hammer the hub bolt to avoid impact to the wheel
hub and bearing assembly.
• Pull out the hub bolt in a direction perpendicular to the
wheel hub and bearing assembly.
11. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
Hub Bolts
• Place a washer
as shown in the figure to install the hub bolts
by using the tightening force of the nut
.
CAUTION:
• Check that there is no clearance between wheel hub and
bearing assembly, and hub bolt.
• Never reuse hub bolt.
Drive shaft
• Tighten the wheel hub lock nut to the specified torque. Refer to
CAUTION:
• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel
hub lock nut.
• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.
• When installing a cotter pin, securely band the basal portion to prevent rattles.
CAUTION:
• Bend cotter pin at the root sufficiently to prevent any looseness.
• Never reuse cotter pin.
Disc rotor
CAUTION:
• Align the matching marks
made during removal when reus-
ing the disc rotor.
• Never drop disc rotor.
• Perform inspection after installation. Refer to
.
JPDIF0299ZZ
JPDIF0300ZZ
JPDIG0066ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст