Nissan X-Trail 32. Instruction — part 536
COMBINATION METER BUZZER
DLK-485
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
COMBINATION METER BUZZER
Component Function Check
INFOID:0000000010717541
1.
CHECK FUNCTION
1.
Turn ignition switch ON.
2.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
3.
Select “INSIDE BUZZER” in “ACTIVE TEST” mode.
4.
Touch “Buzzer 1”, “Buzzer 2” or “Buzzer 3” to check that it works normally.
Is the inspection result normal?
Yes
>> Combination meter buzzer is OK.
No
>> Refer to
DLK-485, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000010717542
1.
CHECK METER BUZZER CIRCUIT
WCS-54, "Component Function Check"
.
Is the inspection result normal?
Yes
>> GO TO 2.
No
>> Repair or replace harness.
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
DLK-486
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
DOOR LOCK ACTUATOR
DOOR LOCK ACTUATOR
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000010717543
1.
CHECK FUNCTION
1.
Turn ignition switch ON.
2.
Select “DOOR LOCK” of “BCM” using CONSULT.
3.
Select “DOOR LOCK” in “ACTIVE TEST” mode.
4.
Touch “ALL LOCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-486, "DRIVER SIDE : Diagnosis Procedure"
.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000010717544
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check voltage between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock assembly (driver side).
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM and front door lock assembly (passenger side) connector.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
(+)
(–)
Condition
Voltage
Front door lock assembly
(driver side)
Connector
Terminal
D9
1
Ground
Door lock and unlock switch
Lock
9 – 16 V
2
Unlock
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M85
141
D9
1
Existed
148
2
BCM
Ground
Continuity
Connector
Terminal
M85
141
Not existed
148
DOOR LOCK ACTUATOR
DLK-487
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Check for internal short of front door lock actuator.
NO
>> Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
PASSENGER SIDE
PASSENGER SIDE : Component Function Check
INFOID:0000000010717545
1.
CHECK FUNCTION
1.
Turn ignition switch ON.
2.
Select “DOOR LOCK” of “BCM” using CONSULT.
3.
Select “DOOR LOCK” in “ACTIVE TEST” mode.
4.
Touch “ALL LOCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-487, "PASSENGER SIDE : Diagnosis Procedure"
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000010717546
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (passenger side) connector.
3.
Check voltage between front door lock assembly (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock assembly (passenger side).
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM and front door lock assembly (driver side) connector.
2.
Check continuity between BCM harness connector and front door lock assembly (passenger side) har-
ness connector.
3.
Check continuity between BCM harness connector and ground.
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M85
141
Ground
Door lock and unlock switch
Lock
9 – 16 V
148
Unlock
(+)
(–)
Condition
Voltage
Front door lock assembly
(passenger side)
Connector
Terminal
D48
5
Ground
Door lock and unlock switch
Lock
9 – 16 V
6
Unlock
BCM
Front door lock assembly (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M85
139
D48
6
Existed
141
5
DLK-488
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 2]
DOOR LOCK ACTUATOR
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of front door lock actuator.
NO
>> Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
REAR LH
REAR LH : Component Function Check
INFOID:0000000010717547
1.
CHECK FUNCTION
1.
Turn ignition switch ON.
2.
Select “DOOR LOCK” of “BCM” using CONSULT.
3.
Select “DOOR LOCK” in “ACTIVE TEST” mode.
4.
Touch “ALL LOCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES
>> Door lock actuator is OK.
NO
>> Refer to
DLK-488, "REAR LH : Diagnosis Procedure"
.
REAR LH : Diagnosis Procedure
INFOID:0000000010717548
1.
CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock assembly LH connector.
3.
Check voltage between rear door lock assembly LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock assembly LH.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and rear door lock assembly RH connector.
2.
Check continuity between BCM harness connector and rear door lock assembly LH harness connector.
BCM
Ground
Continuity
Connector
Terminal
M85
139
Not existed
141
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M85
139
Ground
Door lock and unlock switch
Unlock
9 – 16 V
141
Lock
(+)
(–)
Condition
Voltage
Rear door lock assembly LH
Connector
Terminal
D85
1
Ground
Door lock and unlock switch
Lock
9 – 16 V
2
Unlock
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст