Nissan X-Trail 32. Instruction — part 1932
SN-184
< DTC/CIRCUIT DIAGNOSIS >
[WITH PARK ASSIST]
B2725-12 REAR BUZZER
Is the inspection result normal?
YES
>> Replace buzzer (backward). Refer to
SN-242, "REAR : Removal and Installation"
NO
>> Repair harness or connector.
Sonar control unit
Ground
Standard
Reference value
(Approx.)
Connector
Terminal
B129
9
—
NOTE:
• Voltage depends on volume.
• Cycle depends on distance between sensor
and obstacle.
JSNIA5232GB
SN
B2725-14 REAR BUZZER
SN-185
< DTC/CIRCUIT DIAGNOSIS >
[WITH PARK ASSIST]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B2725-14 REAR BUZZER
DTC Description
INFOID:0000000010920192
DTC DETECTION LOGIC
POSSIBLE CAUSE
Harness between sonar control unit and buzzer (backward)
FAIL-SAFE
• Obstacle detection function is stopped
• Alarm display is displayed on the information display of combination meter
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.
5.
Check DTC.
Is DTC “B2725-14” detected?
YES
>> Proceed to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010920193
1.
CHECK CONTINUITY BUZZER (BACKWARD) POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect sonar control unit connector and buzzer (backward) connector.
3.
Check continuity between sonar control unit harness connector and buzzer (backward) harness connec-
tor.
4.
Check continuity between sonar control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK CONTINUITY BUZZER DRIVE SIGNAL CIRCUIT
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detection condition
B2725-14
REAR BUZZER
(Rear buzzer)
OPEN/SHORT-
GND
(Open/Short to
ground)
A break in harness between sonar control unit and buzzer (back-
ward) or a short circuit between sonar control unit and ground is de-
tected when ignition switch is turned ON.
Sonar control unit
Buzzer (backward)
Continuity
Connector
Terminal
Connector
Terminal
B129
15
B66
2
Existed
Sonar control unit
Ground
Continuity
Connector
Terminal
B129
15
Not existed
SN-186
< DTC/CIRCUIT DIAGNOSIS >
[WITH PARK ASSIST]
B2725-14 REAR BUZZER
1.
Check continuity between sonar control unit harness connector and buzzer (backward) harness connec-
tor.
2.
Check continuity between sonar control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK CONTINUITY SONAR CONTROL UNIT
1.
Check continuity between terminals of sonar control unit.
2.
Check continuity between sonar control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace buzzer (backward). Refer to
SN-242, "REAR : Removal and Installation"
NO
>> Replace sonar control unit. Refer to
SN-237, "Removal and Installation"
.
Sonar control unit
Buzzer (backward)
Continuity
Connector
Terminal
Connector
Terminal
B129
9
B66
3
Existed
Sonar control unit
Ground
Continuity
Connector
Terminal
B129
9
Not existed
Sonar control unit
Continuity.
Terminal
15
9
Not existed
Sonar control unit
Ground
Continuity
Terminal
15
Not existed
9
SN
B2728-11 LED
SN-187
< DTC/CIRCUIT DIAGNOSIS >
[WITH PARK ASSIST]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
B2728-11 LED
DTC Description
INFOID:0000000011009383
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness between sonar control unit and sonar system switch
• Sonar control unit
FAIL-SAFE
• Obstacle detection function is stopped
• Alarm display is displayed on the information display of combination meter
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF and wait at least 30 seconds.
3.
Turn ignition switch ON and wait at least 30 seconds or more.
4.
Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.
5.
Check DTC.
Is DTC B2728-11 detected?
YES
>> Proceed to
.
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000011009384
1.
CHECK SONAR SYSTEM SWITCH INDICATOR SIGNAL CIRCUIT FOR SHORT
1.
Turn ignition switch OFF.
2.
Disconnect sonar control unit harness connector and sonar system switch harness connector.
3.
Check the continuity between sonar control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace sonar control unit. Refer to
SN-237, "Removal and Installation"
.
NO
>> Repair harness or connector.
DTC
Trouble diagnosis
(Trouble diagnosis contents)
Detection condition
B2728-11
LED
(Light emitting diode)
SHORT-GND
(Short to ground)
Short circuit to ground is detected in harness between sonar control
unit and sonar system switch when ignition switch is turned ON.
Sonar control unit
Ground
Continuity
Connector
Terminal
B129
17
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст