Nissan X-Trail 32. Instruction — part 1631
PB-50
< BASIC INSPECTION >
INSTRUCTIONS FOR RELEASING PARKING BRAKE WHERE PARKING
BRAKE SWITCH CANNOT BE USED
INSTRUCTIONS FOR RELEASING PARKING BRAKE WHERE PARKING
BRAKE SWITCH CANNOT BE USED
Description
INFOID:0000000010722935
Disconnecting the battery negative terminal with the parking brake on, prevents the parking brake from releas-
ing. Releasing is performed mechanically.
Work Procedure
INFOID:0000000010722936
1.
DISCONNECT PARKING BRAKE ACTUATOR HARNES CONNECTOR
1.
Disconnect the parking brake actuator harness connector
from the rear caliper assembly
.
>> GO TO 2.
2.
REMOVE PARKING BRAKE ACTUATOR
Remove the parking brake actuator
from the rear brake caliper
assembly .
>> GO TO 3.
3.
RELEASE OF PARKING BRAKE
Rotate the rear brake caliper assembly
spindle part
clockwise.
Is the parking brake released?
YES
>> GO TO 4.
NO
>>
Check the rear brake caliper assembly.
• LHD models: Refer to
ASSEMBLY : Inspection and Adjustment"
.
ASSEMBLY : Inspection and Adjustment"
.
4.
REPLACE REAR CALIPER ASSEMBLY
Replace the rear caliper assembly.
• LHD models: Refer to
BR-63, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
• RHD models: Refer to
BR-123, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
CAUTION:
Never reuse the parking brake actuator.
>> End of work.
JSFIA2443ZZ
JSFIA2426ZZ
JSFIA2444ZZ
ADDITIONAL SERVICE WHEN REPLACING ELECTRIC PARKING BRAKE CON-
TROL MODULE
PB-51
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
ADDITIONAL SERVICE WHEN REPLACING ELECTRIC PARKING BRAKE
CONTROL MODULE
Work Procedure
INFOID:0000000010722937
When replacing the electric parking brake control module be sure to perform the following procedure.
1.
CONFIGURATION
Perform the configuration. Refer to
.
>> GO TO 2.
2.
CALIBRATION OF G SENSOR
Perform the calibration of G sensor. Refer to
.
M/T models>>GO TO 3.
CVT models>>GO TO 4.
3.
RESET OF CLUTCH PEDAL STROKE SENSOR (M/T MODELS)
Perform the reset of clutch stroke sensor. Refer to
>> GO TO 5.
4.
AUTOMATIC ACTIVATION ON SETTING (CVT MODELS)
Perform the automatic activation ON setting: Refer to
.
>> GO TO 5.
5.
ADJUSTMENT OF REAR BRAKE CALIPER INITIAL POSITION
Perform the adjustment of rear brake caliper initial position: Refer to
>> GO TO 6.
6.
OPERATION OF REAR BRAKE CALIPER
Perform the operation of rear brake caliper: Refer to
>> GO TO 7.
7.
RELEASE OF REAR BRAKE CALIPER
Perform the release of rear brake caliper: Refer to
>> GO TO 8.
8.
CHANGE OF SYSTEM MODE
Perform the change of system mode: Refer to
>> End of work.
PB-52
< BASIC INSPECTION >
REPLACEMENT OF REAR BRAKE PAD
REPLACEMENT OF REAR BRAKE PAD
Description
INFOID:0000000010722938
CAUTION:
When performing the following operations, always use CONSULT, for performing “START BRAKE PAD
REPLACEMENT”, “FINISH BRAKE PAD REPLACEMENT”, “INITIALIZATION POSITION ADJUSTMENT”,
“BRAKE OPERATION” and “BRAKE RELEASE” of “WORK SUPPORT”.
×
: Required
—: not required
*: M/T models
Work Procedure
INFOID:0000000010722939
CAUTION:
When performing the following operations, always use CONSULT. (It cannot be performed by any
means other than CONSULT.)
• Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly)
• Replacing rear brake pad
• Replacing rear brake caliper assembly
1.
BEFORE REMOVAL/REPLACEMENT OF REAR BRAKE PAD OR REAR CALIPER ASSEMBLY
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Never start the engine.
2.
Select “EHS/PKB”, “WORK SUPPORT”, and “START BRAKE PAD REPLACEMENT” according to this
order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
3.
Touch “START”.
>> GO TO 2.
2.
REMOVAL AND INSTALLATION/REPLACEMENT OF REAR BRAKE PAD OR REAR BRAKE CALIPER
Procedure
• START BRAKE PAD REPLACEMENT
• FINISH BRAKE PAD REPLACEMENT
• INITIALIZATION POSITION ADJUSTMENT
• BRAKE OPERATION
• BRAKE RELEASE
Removing/installing electric parking brake control module
—
Replacing electric parking brake control module
—
Removing/installing rear brake pad (When not pressing piston of rear
brake caliper assembly)
—
Removing/installing rear brake pad (When pressing piston of rear brake
caliper assembly)
×
Replacing rear brake pad
×
Removing/installing rear brake caliper assembly
—
Replacing rear brake caliper assembly
×
Removing/installing parking brake switch
—
Replacing parking brake switch
—
Removing/installing clutch stroke sensor
*
—
Replacing clutch stroke sensor
*
—
Removing/installing clutch pedal
*
—
Replacing clutch pedal
*
—
REPLACEMENT OF REAR BRAKE PAD
PB-53
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
ASSEMBLY
Replace the rear brake pad or rear brake caliper.
• Rear brake pad
- LHD models: Refer to
BR-60, "BRAKE PAD : Removal and Installation"
.
- RHD models: Refer to
BR-120, "BRAKE PAD : Removal and Installation"
.
• Rear brake caliper assembly
- LHD models: Refer to
BR-63, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
- RHD models: Refer to
BR-123, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
>> GO TO 3.
3.
AFTER INSTALLATION/REPLACEMENT OF REAR BRAKE PAD OR REAR CALIPER ASSEMBLY
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “FINISH BRAKE PAD REPLACEMENT” according to this
order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
2.
Touch “START”.
>> GO TO 4.
4.
PERFORM INITIALIZATION POSITION ADJUSTMENT
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “INITIALIZATION POSITION ADJUSTMENT” according to
this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
2.
Touch “START”.
>> GO TO 5.
5.
PERFORM BRAKE OPERATION
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE OPERATION” according to this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
2.
Touch “START”.
>> GO TO 6.
6.
PERFORM BRAKE RELEASE
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE RELEASE” according to this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
2.
Touch “START”.
>> GO TO 7.
7.
PERFORM THE SELF-DIAGNOSIS
With CONSULT
1.
Pull parking brake switch to activate electric parking brake.
2.
Push parking brake switch to release electric parking brake.
3.
Perform “EHS/PKB” self-diagnosis.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст