Nissan X-Trail 32. Instruction — part 1280
FAX-112
< REMOVAL AND INSTALLATION >
[4WD]
FRONT DRIVE SHAFT
Shaft
Check shaft for runout, cracks, or other damage. Replace if there are.
Dynamic Damper
Check damper for cracks or wear. Replace if necessary.
Joint Sub-Assembly (Wheel Side)
Check the following:
• Joint sub-assembly for rough rotation and excessive axial looseness
• The inside of the joint sub-assembly for entry of foreign material
• Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly
Replace joint sub-assembly if there are any non-standard conditions of components.
Housing and Spider assembly (Transaxle Side)
Replace housing and spider assembly if there is scratching or wear of housing roller contact surface or spider
roller contact surface.
NOTE:
Housing and spider assembly are used in a set.
Support Bearing (Right Side)
Make sure wheel bearing rolls freely and is free from noise, cracks, pitting or wear. Replace support bearing if
there are any non-standard conditions.
Support Bearing Bracket (Right Side)
Check for bending, cracks, or damage. Replace support bearing bracket if there are any non-standard condi-
tions.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
BRC-212, "FRONT WHEEL SENSOR :
.
2.
Check the wheel alignment. Refer to
.
3.
Adjust neutral position of steering angle sensor. Refer to
.
QR25DE
QR25DE : Exploded View
INFOID:0000000010824420
LEFT SIDE
JSDIA6398ZZ
Circular clip
Dust shield
Housing
Snap ring
Spider assembly
Stopper ring
Boot band
Boot
Shaft
Damper band
Dynamic damper
Joint sub-assembly
FRONT DRIVE SHAFT
FAX-113
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
RIGHT SIDE
QR25DE : Removal and Installation
INFOID:0000000010824421
REMOVAL
Left Side
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Remove wheel sensor from steering knuckle. Refer to
BRC-212, "FRONT WHEEL SENSOR : Removal
Dust shield
: Wheel side
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)]
: Always replace after every disassembly.
JSDIA6399GB
Dust shield
Joint sub-assembly
Circular clip
Boot band
Boot
Shaft
Damper band
Dynamic damper
Stopper ring
Spider assembly
Snap ring
Housing
Dust shield
Support bearing
Retainer
Support bearing bracket
: Wheel side
1: Fill NISSAN Genuine grease or equivalent.
2: Apply paste [service parts (440037S000)].
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
FAX-114
< REMOVAL AND INSTALLATION >
[4WD]
FRONT DRIVE SHAFT
3.
Remove lock plate
from strut assembly.
• LHD: Refer to
BR-24, "FRONT : Exploded View"
.
• RHD: Refer to
BR-88, "FRONT : Exploded View"
4.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work.
• LHD (1 PISTON TYPE): Refer to
BR-51, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• LHD (2 PISTON TYPE): Refer to
BR-56, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
• RHD (1 PISTON TYPE): Refer to
BR-111, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• RHD (2 PISTON TYPE): Refer to
BR-116, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor. Refer to
FAX-72, "Removal and Installation"
.
6.
Remove cotter pin, adjusting cap and then loosen wheel hub
lock nut, using a hub lock nut wrench (A) (SST: KV40104000).
7.
Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub and bearing assembly from drive
shaft.
NOTE:
Use suitable puller, if wheel hub and bearing assembly and drive
shaft cannot be separated even after performing the above pro-
cedure.
8.
Remove wheel hub lock nut.
9.
Remove transverse link from steering knuckle and front suspension member. Refer to
10. Separate steering outer socket from steering knuckle. Refer to
ST-22, "Removal and Installation"
JSDIA3795ZZ
JSDIA2708ZZ
JPDIG0070ZZ
FRONT DRIVE SHAFT
FAX-115
< REMOVAL AND INSTALLATION >
[4WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
11. Remove drive shaft from wheel hub and bearing assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle.
• Be careful not to overextend slide joint.
12. Remove drive shaft from transaxle assembly.
• Use the drive shaft attachment (A) (SST: KV40107500) and a
sliding hammer (B) (commercial service tool) while inserting
tip of the drive shaft attachment between housing and tran-
saxle assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle when
removing drive shaft. Also be careful not to overextend
slide joint.
• Confirm that the circular clip is attached to the drive
shaft.
Right Side
1.
Remove tires. Refer to
WT-61, "Removal and Installation"
.
2.
Remove wheel sensor from steering knuckle. Refer to
BRC-212, "FRONT WHEEL SENSOR : Removal
3.
Remove lock plate
from strut assembly.
• LHD: Refer to
BR-24, "FRONT : Exploded View"
.
• RHD: Refer to
BR-88, "FRONT : Exploded View"
4.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work.
• LHD (1 PISTON TYPE): Refer to
BR-51, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• LHD (2 PISTON TYPE): Refer to
BR-56, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
• RHD (1 PISTON TYPE): Refer to
BR-111, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal
• RHD (2 PISTON TYPE): Refer to
BR-116, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal
CAUTION:
Never depress brake pedal while brake caliper is removed.
5.
Remove disc rotor. Refer to
FAX-72, "Removal and Installation"
.
JSDIA5562ZZ
JPDIF0004ZZ
JSDIA3795ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст