Nissan X-Trail 32. Instruction — part 1229
HEADLAMP AIMING ADJUSTMENT
EXL-373
< PERIODIC MAINTENANCE >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Unit: mm (in)
Distance from headlamp center to screen (L)
: 10 m (32.8 ft)
Aiming adjustment area
Vertical direction (Y)
(Lower side from headlamp center height)
Lateral direction (X)
(Left side from headlamp center line)
Highest light axis
100 (3.94)
0 - 100 (3.94)
Target light axis
100 (3.94)
Lowest light axis
130 (5.12)
EXL-374
< PERIODIC MAINTENANCE >
[HALOGEN HEADLAMP]
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
Description
INFOID:0000000011008556
PREPARATION BEFORE ADJUSTING
NOTE:
For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Never remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.).
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
• Turn the aiming adjusting screw for adjustment.
Aiming Adjustment Procedure
INFOID:0000000011008557
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3.
Start the engine. Turn the front fog lamp ON.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
4.
Adjust the cutoff line height
with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and
becomes 150 mm (5.90 in).
Front fog lamp light distribution on the screen
: DOWN
: UP
JMLIA4843ZZ
: Cutoff line
: High illuminance area
H
: Horizontal center line of front fog lamp
V
: Vertical center line of front fog lamp
X
: Cutoff line height
JPLIA0008ZZ
FRONT COMBINATION LAMP
EXL-375
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REMOVAL AND INSTALLATION
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000010789898
REMOVAL
DISASSEMBLY
Front fender panel
Front combination lamp
: Vehicle front
: N·m (kg-m, in-lb)
JMLIA4944GB
EXL-376
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
FRONT COMBINATION LAMP
Removal and Installation
INFOID:0000000010789899
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-214, "Precautions for Removing Battery Terminal"
REMOVAL
1.
Remove front bumper fascia. Refer to
EXT-15, "Removal and Installation"
.
2.
Remove front combination lamp assembly mounting bolts and clip.
3.
Remove harness clip of front combination lamp bracket.
4.
Pull out front combination lamp forward the vehicle.
5.
Disconnect front combination lamp harness connectors, and then remove front combination lamp.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, perform aiming adjustment. Refer to the following:
• LHD MODELS: Refer to
EXL-369, "LHD MODELS : Description"
• RHD MODELS: Refer to
EXL-371, "RHD MODELS : Description"
.
Replacement
INFOID:0000000010789900
CAUTION:
Front combination lamp housing
Headlamp bulb (Lo)
Socket cover
Back cover
Front combination lamp harness
Front combination lamp bracket
Front turn signal lamp bulb
Front turn signal lamp bulb socket
Headlamp bulb (Hi)
: Vehicle front
JMLIA4946ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст