Nissan X-Trail 32. Instruction — part 1600
MWI-82
< SYSTEM DESCRIPTION >
OPERATION
OPERATION
Switch Name and Function
INFOID:0000000010714995
STEERING SWITCH
• The steering switch is located on the steering wheel.
• Transmits the steering switch signal to the combination meter.
METER CONTROL SWITCH
• The illumination control switch is located on the instrument finisher
A.
• Transmits the following signals to the combination meter.
- Trip reset switch signal
- Illumination control switch signal (+)
- Illumination control switch signal (
−
)
JSNIA7195ZZ
No.
Switch name
Operation
Description
Back switch
Press
• Switches the screen shown on the information display to the previous
screen.
• Switches the screen shown on the information display to the previous
screen.
ENTER switch
Press
Confirms each item displayed on the information display.
Press and
hold
• When pressed for 1 second or more with an average vehicle speed or fuel
economy (average fuel consumption, ECO pedal guide) displayed on the in-
formation display, the displayed value (average vehicle speed or average
fuel consumption) can be reset.
• When pressed for 3 second or more with an average vehicle speed or fuel
economy (average fuel consumption, ECO pedal guide) displayed on the in-
formation display, a new screen appears and average vehicle speed and
average fuel consumption can be simultaneously reset.
Push up
• Switches the screen shown on the information display to the previous
screen.
• Moves up the item selected on the information display.
• Increases the set value displayed on the settings screen of the information
display.
Push down
• Switches the screen shown on the information display to the next screen.
• Moves down the item selected on the information display.
• Decreases the set value displayed on the settings screen of the information
display.
JSNIA7197ZZ
MWI
OPERATION
MWI-83
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
No.
Switch name
Operation
Description
Illumination control switch (
−
)
Press
An illuminance level of the back light of the combination meter can be adjusted.
Illumination control switch (+)
Trip reset switch
Press
• The trip meter can be switched between A and B.
• Trip meter A/B can be reset by pressing and holding the trip reset switch.
MWI-84
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (COMBINATION METER)
DIAGNOSIS SYSTEM (COMBINATION METER)
On Board Diagnosis Function
INFOID:0000000010714996
COMBINATION METER SELF-DIAGNOSIS MODE
The following meter functions can be checked during Combination Meter Self-Diagnosis Mode:
• Pointer sweep of speedometer, tachometer and gauges.
• Illumination of LCD color patterns for meter displays.
• Illumination of all lamps/LEDs that are controlled by the combination meter.
• Error code
STARTING COMBINATION METER SELF-DIAGNOSIS MODE
How to Initiate Self-Diagnosis Mode
1.
Turn ignition switch OFF.
2.
While pressing the trip reset switch
, turn ignition switch ON.
3.
Keep the trip reset switch for 1 seconds or more.
4.
Press the trip reset switch at least 3 times. (Within 7 seconds
after the ignition switch is turned ON.)
5.
“Work instruction code” is indicated in the top portion of informa-
tion display and self-diagnosis is started.
NOTE:
When on-board diagnosis does not start, check the following
items and replace combination meter if the check results are
normal.
• Combination meter power supply and ground circuits. Refer to
MWI-129, "COMBINATION METER : Diagnosis Procedure"
.
• Meter control switch signal circuits. Refer to
MWI-134, "Component Function Check"
6.
The mode switches in the order shown below each time the trip reset switch is pressed.
NOTE:
If the trip reset switch is not operated for 20 seconds or more, the self-diagnosis mode is automatically
cancelled.
JSNIA7183ZZ
Test order
Test item
Description
1
Work instruction code
This item is displayed, but not used.
2
Software code
3
EEPROM code
4
Hardware code
5
P.C.B code
6
Circuit check
The pointer of the following items moves from 0 to MAX twice.
• Speedometer
• Tachometer
• Engine coolant temperature gauge
• Fuel gauge
NOTE:
If any one of the pointers does not sweep, replace combination meter.
7
Color check
*1
Performs the color check of the information display.
8
Error code
*2
Displays the error code of the following items.
• Speedometer
• Tachometer
• Engine coolant temperature gauge
• Fuel gauge
• Meter control switch
9
Warning/indicator lamp check
All warning/indicator lamp illuminate.
NOTE:
• When either one of them does not turn ON, replace combination meter.
• SRS air bag warning lamp and security indicator lamp are not illuminate.
MWI
DIAGNOSIS SYSTEM (COMBINATION METER)
MWI-85
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
*1: Color Check
*2: Error Code
Blue
Red
Pink
Green
Light blue
Yellow
White
White
Black
Light blue
Black
Pink
Black
Blue
Black
Dark blue
White
Blue
JSNIA5944ZZ
JSNIA5945ZZ
Item
Code
Description
Action to take/Reference
Speedometer
0
Normal
—
1
A vehicle speed signal cannot be received
from ABS actuator and electric unit (control
unit).
Perform “Self Diagnostic Result” of
“ABS.”
Refer to
2
A vehicle speed signal received from the
ABS actuator and electric unit (control unit)
is abnormal.
Tachometer
0
Normal
—
1
An engine speed signal cannot be received
from TCM.
Perform “Self Diagnostic Result” of
“TCM.”
Refer to
(RE0F10D), or
(RE0F10G)
Fuel gauge
0
Normal
—
1
Fuel gauge circuit is short.
2
Fuel gauge circuit is open.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст