Nissan X-Trail 32. Instruction — part 1620
PB-6
< PRECAUTION >
PRECAUTIONS
2.
Turn key switch to the OFF position with the driver side door opened.
3.
Get out of the vehicle and close the driver side door.
4.
Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
5.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
INSTRUCTION 2 (FOR VEHICLES PARKED BY IGNITION SWITCH OFF)
1.
Unlock the door with intelligent key or remote keyless entry.
NOTE:
At this moment, ACC power is supplied.
2.
Open the driver side door.
3.
Open the hood.
4.
Close the driver side door.
5.
Wait at least 3 minutes.
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
6.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
Precaution for Stop/Start System Service
INFOID:0000000011003165
CAUTION:
When performing an inspection and its related work with the engine at idle, always turn the stop/start
OFF switch ON or open the hood to release the stop/start system.
Precautions for Harness Repair
INFOID:0000000010735273
• Solder the repaired area and wrap tape around the soldered area.
NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).
D4D engine
: 20 minutes
HRA2DDT
: 12 minutes
K9K engine
: 4 minutes
M9R engine
: 4 minutes
R9M engine
: 4 minutes
V9X engine
: 4 minutes
SKIB8766E
PRECAUTIONS
PB-7
< PRECAUTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
• Bypass connection is never allowed at the repaired area.
NOTE:
Bypass connection may cause CAN communication error. The
spliced wire becomes separated and the characteristics of twisted
line are lost.
• Replace the applicable harness as an assembly if error is detected on the shield lines of CAN communica-
tion line.
Precaution for Parking Brake System
INFOID:0000000010722914
WARNING:
Since dust covering the rear brakes has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
• When the parking brake is operated, the electric parking brake indicator lamp in the combination meter and
the parking brake switch indicator turn ON.
• When a following malfunction occurs in the electric parking brake system, the brake system warning lamp
and parking brake switch indicator turn blink.
- When a status cannot be judged between applied and released.
- When the parking brake switch is operated under the condition that the parking brake switch is malfunction.
- When the parking brake switch is operated under the condition that the parking brake actuator is malfunc-
tion.
- When the initial position adjustment of the parking brake actuator is incomplete.
- When a peaking brake system mode is factory mode
CAUTION:
When vehicle is parked, selector lever is in the P position.
• When a malfunction occurs in the electric parking brake system, parking brake can be mechanically
released. Refer to
• When parking brake must be released while the battery negative terminal is disconnected, mechanically
release it. Refer to
.
• When rear brake pad is ground or replaced, perform break-in operation.
- LHD models: Refer to
BR-19, "BRAKE PAD : Inspection and Adjustment"
.
- RHD models: Refer to
BR-83, "BRAKE PAD : Inspection and Adjustment"
• When rear disc rotor is ground or replaced, perform break-in operation.
- LHD models: Refer to
BR-19, "DISC ROTOR : Inspection and Adjustment"
.
- RHD models: Refer to
BR-83, "DISC ROTOR : Inspection and Adjustment"
SKIB8767E
PB-8
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000010722916
LHD models
Center console
Clutch pedal
Under center console
Rear brake caliper assembly
JSFIA2498ZZ
No.
Component part
Function
Parking brake actuator (RH)
PB-12, "Parking Brake Actuator"
Rear brake caliper assembly (RH)
Parking brake actuator harness
COMPONENT PARTS
PB-9
< SYSTEM DESCRIPTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
*1: CVT models
*2: M/T models
RHD models
Combination meter
Mainly transmits the following signal to electric parking brake control module via
CAN communication.
• Seat belt buckle switch (driver side) signal
Mainly receives the following signals from electric parking brake control module
via CAN communication.
• Electric parking brake indicator lamp signal
• Brake system warning lamp signal
• Master warning lamp signal
• Electric parking brake display request signal
Refer to
MWI-7, "METER SYSTEM : Component Parts Location"
for detailed in-
stallation location.
ABS actuator and electric unit (control unit)
Mainly transmits the following signal to electric parking brake control module via
CAN communication.
• Rear LH wheel speed signal
• Rear RH wheel speed signal
• VDC operation signal
• Brake fluid pressure signal
• ABS operation signal
Refer to
BRC-14, "Component Parts Location"
for detailed installation location.
TCM
*1
Mainly transmits the following signal to electric parking brake control module via
CAN communication.
• Target gear position signal
Refer to
TM-235, "CVT CONTROL SYSTEM : Component Parts Location"
oline engine models),
TM-466, "CVT CONTROL SYSTEM : Component Parts Lo-
(diesel engine models) for detailed installation location.
ECM
Mainly transmits the following signal to electric parking brake control module via
CAN communication.
• Engine speed signal
• Engine torque signal
Refer to
EC-28, "ENGINE CONTROL SYSTEM : Component Parts Location"
(MR20DD engine models),
EC-440, "Component Parts Location"
(QR25DE en-
gine models),
EC-812, "Component Parts Location"
(R9M engine models) for de-
tailed installation location.
IPDM E/R
Mainly transmits the following signal to electric parking brake control module via
CAN communication.
• Ignition switch ON signal
Refer to
PCS-5, "Component Parts Location"
for detailed installation location.
BCM
Mainly transmits the following signal to electric parking brake control module via
CAN communication.
• Stop lamp switch signal
• Steering lock status signal
• Wake up sleep command signal
• Door switch (driver side) signal
Refer to
BCS-6, "BODY CONTROL SYSTEM : Component Parts Location"
for de-
tailed installation location.
Parking brake switch
Clutch pedal stroke sensor
*2
PB-12, "Clutch Pedal Stroke Sensor"
Electric parking brake control module
PB-12, "Electric Parking Brake Control Module"
Rear brake caliper assembly (LH)
PB-12, "Parking Brake Actuator"
Parking brake actuator harness
Parking brake actuator (LH)
No.
Component part
Function
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст