Nissan X-Trail 32. Instruction — part 1957
SR-42
< REMOVAL AND INSTALLATION >
DISPOSAL OF AIR BAG MODULE
Deployed air bag module, seat belt pre-tensioner, and lap pre-tensioner are very hot. Before disposing of air
bag module and seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a
plastic bag before disposal.
CAUTION:
• Never apply water to a deployed air bag module or seat belt
pre-tensioner or lap pre-tensioner.
• Wear gloves when handling a deployed air bag module or seat
belt pre-tensioner or lap pre-tensioner.
• No poisonous gas is produced upon air bag module deploy-
ment. However, be careful not to inhale gas since it irritates
the throat and can cause choking.
• Never disassemble air bag module, seat belt pre-tensioner
and lap pre-tensioner.
• Air bag module, seat belt pre-tensioner and lap pre-tensioner
cannot be reused.
• Wash your hands clean after the work is complete.
SIDE AIR BAG MODULE
SIDE AIR BAG MODULE : Deployment
INFOID:0000000010927748
DEPLOYMENT OF SIDE AIR BAG MODULE (OUTSIDE OF VEHICLE)
1.
Make 6.5 mm (0.256 in) diameter hole
in air bag module
bracket (SST: KV99105300) (A) at the position shown in figure.
2.
Firmly secure air bag module bracket (SST: KV99105300) in a
vise.
3.
Insert two bolts through air bag module bracket and side air bag
module
upper side holes, and fix them with two nuts
.
4.
Connect deployment tool (SST: KV99104600) (A) and deploy-
ment tool adapter (SST: KV99108300) (B) to side air bag mod-
ule connector.
5.
Connect the test pin at the tip of deployment tool (SST:
KV99104600) (B) to both terminals of 12V battery (A), and then
the air bag module deploys.
CAUTION:
When deploying the side air bag module, stand at least 5.0
m (16.4 ft) away from the side air bag module.
SBF276H
JMHIA0225ZZ
JMHIA0284ZZ
JMHIA0062ZZ
DISPOSAL OF AIR BAG MODULE
SR-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE AIR BAG MODULE : Disposal
INFOID:0000000010927749
DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
Deployed air bag module, seat belt pre-tensioner, and lap pre-tensioner are very hot. Before disposing of air
bag module and seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a
plastic bag before disposal.
CAUTION:
• Never apply water to a deployed air bag module or seat belt
pre-tensioner or lap pre-tensioner.
• Wear gloves when handling a deployed air bag module or seat
belt pre-tensioner or lap pre-tensioner.
• No poisonous gas is produced upon air bag module deploy-
ment. However, be careful not to inhale gas since it irritates
the throat and can cause choking.
• Never disassemble air bag module, seat belt pre-tensioner
and lap pre-tensioner.
• Air bag module, seat belt pre-tensioner and lap pre-tensioner
cannot be reused.
• Wash your hands clean after the work is complete.
CURTAIN AIR BAG MODULE
CURTAIN AIR BAG MODULE : Deployment
INFOID:0000000010927750
DEPLOYMENT OF CURTAIN AIR BAG MODULE (OUTSIDE OF VEHICLE)
1.
Remove rings
, and then remove bracket
.
2.
Cut the inflator
from curtain air bag module
.
3.
Connect deployment tool (SST: KV99104600) (A) and deploy-
ment tool adapter (SST: KV99110500) (B) to the inflator
.
4.
Put the inflator
connected with the deployment tool (A) (SST:
KV99104600) and deployment tool adapter (B) (SST:
KV99110500) into a tire without a wheel (C).
SBF276H
JMHIA2653ZZ
JMHIA1634ZZ
JMHIA0066ZZ
SR-44
< REMOVAL AND INSTALLATION >
DISPOSAL OF AIR BAG MODULE
5.
Put the tire with the inflator onto another tire without a wheel.
Add an additional tire without a wheel and then a tire mounted
on a wheel on top, and then tie all tires together with a strap (C)
in order keep them standing.
6.
Connect the test pin at the tip of deployment tool (SST:
KV99104600) (A) to both terminals of 12V battery (B), and then
the air bag module deploys.
CAUTION:
When deploying the curtain air bag module, stand at least
5.0 m (16.4 ft) away from the curtain air bag module.
CURTAIN AIR BAG MODULE : Disposal
INFOID:0000000010927751
DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
Deployed air bag module, seat belt pre-tensioner, and lap pre-tensioner are very hot. Before disposing of air
bag module and seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a
plastic bag before disposal.
CAUTION:
• Never apply water to a deployed air bag module or seat belt
pre-tensioner or lap pre-tensioner.
• Wear gloves when handling a deployed air bag module or seat
belt pre-tensioner or lap pre-tensioner.
• No poisonous gas is produced upon air bag module deploy-
ment. However, be careful not to inhale gas since it irritates
the throat and can cause choking.
• Never disassemble air bag module, seat belt pre-tensioner
and lap pre-tensioner.
• Air bag module, seat belt pre-tensioner and lap pre-tensioner
cannot be reused.
• Wash your hands clean after the work is complete.
SEAT BELT PRE-TENSIONER
SEAT BELT PRE-TENSIONER : Deployment
INFOID:0000000010927752
DEPLOYMENT OF SEAT BELT PRE-TENSIONER (OUTSIDE OF VEHICLE)
1.
Firmly grip seat belt pre-tensioner
in a vise (A) and cut off the
webbing .
JMHIA0067ZZ
SBF276H
JMHIA2295ZZ
DISPOSAL OF AIR BAG MODULE
SR-45
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
2.
Connect deployment tool (SST: KV99104600) (B) and deploy-
ment tool adapter (SST: KV99110500) (A) yellow connector to
seat belt pre-tensioner.
3.
Connect the test pin at the tip of deployment tool (SST:
KV99104600) (B) to both terminals of 12V battery (C), and then
the seat belt pre-tensioner.
CAUTION:
When deploying the seat belt pre-tensioner, stand at least
5.0 m(16.4 ft) away from the seat belt pre-tensioner.
SEAT BELT PRE-TENSIONER : Disposal
INFOID:0000000010927753
DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
Deployed air bag module, seat belt pre-tensioner, and lap pre-tensioner are very hot. Before disposing of air
bag module and seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a
plastic bag before disposal.
CAUTION:
• Never apply water to a deployed air bag module or seat belt
pre-tensioner or lap pre-tensioner.
• Wear gloves when handling a deployed air bag module or seat
belt pre-tensioner or lap pre-tensioner.
• No poisonous gas is produced upon air bag module deploy-
ment. However, be careful not to inhale gas since it irritates
the throat and can cause choking.
• Never disassemble air bag module, seat belt pre-tensioner
and lap pre-tensioner.
• Air bag module, seat belt pre-tensioner and lap pre-tensioner
cannot be reused.
• Wash your hands clean after the work is complete.
LAP PRE-TENSIONER
LAP PRE-TENSIONER : Deployment
INFOID:0000000010927754
DEPLOYMENT OF LAP PRE-TENSIONER (OUTSIDE OF VEHICLE)
1.
Cut off the webbing.
JMHIA2296ZZ
SBF276H
JMHIA2656ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст