Nissan X-Trail 32. Instruction — part 2017
TM-26
< SYMPTOM DIAGNOSIS >
[6MT: RS6F94R]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000010842442
Use the chart below to find the cause of the symptom. The numbers indicate the order of the inspection. If nec-
essary, repair or replace these parts.
SUSPECTED PARTS
(Possible cause)
OIL
(Oil
lev
e
l is
l
o
w)
OI
L (W
ro
ng
oi
l)
OIL
(Oil
lev
e
l is
h
igh
)
GASKE
T (Damaged)
OIL SEAL (W
orn or
damaged)
O-RING (W
orn
or
da
ma
ge
d)
SHIF
T CONTROL L
INKAGE
(W
o
rn)
SHIF
T FORK (W
o
rn)
GEAR (W
o
rn o
r da
m
age
d)
BEAR
ING
(W
orn
o
r
da
ma
ge
d)
BAUL
K
RING (W
orn
o
r da
ma
ge
d)
INSE
R
T
S
P
RING (Dam
ag
ed
)
Reference
Symptoms
Noise
1
2
3
3
Oil leakage
3
1
2
2
2
Hard to shift or will not shift
1
1
2
3
3
Jumps out of gear
1
2
2
M/T OIL
TM-27
< PERIODIC MAINTENANCE >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PERIODIC MAINTENANCE
M/T OIL
Inspection
INFOID:0000000010842443
OIL LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
OIL LEVEL
1.
Check oil level from filler plug mounting hole as shown in the fig-
ure, after removing filler plug
and gasket from transaxle
assembly.
CAUTION:
Turn the ignition switch OFF while checking oil level.
2.
Set a gasket on filler plug and install it on transaxle assembly.
CAUTION:
Never reuse gasket.
3.
Tighten filler plug to the specified torque. Refer to
Draining
INFOID:0000000010842444
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug
and gasket, then drain gear
oil.
3.
Set a gasket on drain plug and install it to transaxle assembly.
CAUTION:
Never reuse gasket.
4.
Tighten drain plug to the specified torque. Refer to
Refilling
INFOID:0000000010842445
1.
Fill with new gear oil until oil level reaches the specified level
at filler plug mounting hole, after removing filler plug
and gas-
ket from transaxle assembly.
2.
After refilling gear oil, check the oil level. Refer to
3.
Set a gasket on filler plug, and install it to transaxle assembly.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque. Refer to
JSDIA5819ZZ
JSDIA5820ZZ
Recommended
oil and capacity
: Refer to
.
JSDIA6128ZZ
TM-28
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
M/T SHIFT SELECTOR
REMOVAL AND INSTALLATION
M/T SHIFT SELECTOR
Exploded View
INFOID:0000000010842446
Removal and Installation
INFOID:0000000010842447
REMOVAL
1.
Shift shift lever to the neutral position.
2.
Remove ornament
from shift lever knob
.
CAUTION:
Never damage ornament and shift lever knob.
3.
Pull out retainer
using suitable pliers.
Ornament
Retainer
Shift lever knob
M/T shift selector assembly
M/T shift selector bracket
: N·m (kg-m, in-lb)
JSDIA6131GB
JSDIA6132ZZ
JSDIA6134ZZ
M/T SHIFT SELECTOR
TM-29
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Turn shift lever knob
counterclockwise (30 degrees) and
remove it straight from the shift lever
.
5.
Remove center console assembly. Refer to
.
6.
Disconnect and remove shift cable and select cable from M/T
shift selector assembly. Refer to
7.
Remove M/T shift selector assembly
from M/T shift selector
bracket .
8.
Remove M/T shift selector bracket
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• For each tightening torque, refer to
• Install shift lever knob to the shift lever, as per the following procedure.
CAUTION:
Never reuse shift lever knob.
1.
Set retainer and ornament into shift lever knob.
2.
Displace shift lever knob
counterclockwise (30 degrees) and
insert it straight to the shift lever
without pressing the orna-
ment .
JSDIA6135ZZ
JSDIA5749ZZ
JSDIA5750ZZ
: Vehicle front
JSDIA6032ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст