Nissan X-Trail 32. Instruction — part 1685
PCS-110
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH
PUSH-BUTTON IGNITION SWITCH
Component Function Check
INFOID:0000000010741756
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” in “BCM” using CONSULT.
2.
Select “PUSH SW” in “Data Monitor” mode with CONSULT.
3.
Check that the function operates normally according to the following conditions.
Is the indication normal?
YES
>> INSPECTION END.
NO
>> Refer to
PCS-110, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010741757
1.
CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL 1
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector and IPDM E/R connector.
3.
Check voltage between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT 1
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and push-button ignition switch harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-121, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL 2
1.
Disconnect BCM connector.
2.
Connect IPDM E/R connector.
3.
Check voltage between IPDM E/R harness connector and ground.
Test item
Condition
Status
PUSH SW
Push-button ignition switch is pressed
ON
Push-button ignition switch is not pressed
OFF
(+)
(–)
Voltage
Push-button ignition switch
Connector
Terminal
M16
8
Ground
9 – 16 V
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M86
101
M16
8
Existed
BCM
Ground
Continuity
Connector
Terminal
M86
101
Not existed
PCS
PUSH-BUTTON IGNITION SWITCH
PCS-111
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT 2
1.
Check continuity between IPDM E/R harness connector and push-button ignition switch harness connec-
tor.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-60, "Removal and Installation"
.
NO
>> Repair or replace harness.
5.
CHECK PUSH-BUTTON IGNITION SWITCH GROUND CIRCUIT
Check continuity between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK PUSH-BUTTON IGNITION SWITCH
PCS-111, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace push-button ignition switch. Refer to
PCS-116, "Removal and Installation"
.
7.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000010741758
1.
CHECK PUSH-BUTTON IGNITION SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector.
3.
Check continuity between push-button ignition switch terminals.
(+)
(–)
Voltage
IPDM E/R
Connector
Terminal
E12
38
Ground
6 – 16 V
IPDM E/R
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
E12
38
M16
8
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E12
38
Not existed
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M16
4
Existed
PCS-112
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace push-button ignition switch. Refer to
PCS-116, "Removal and Installation"
.
Push-button ignition switch
Condition
Continuity
Terminal
4
8
Pressed
Existed
Not pressed
Not existed
PCS
PUSH-BUTTON IGNITION SWITCH DOES NOT OPERATE
PCS-113
< SYMPTOM DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYMPTOM DIAGNOSIS
PUSH-BUTTON IGNITION SWITCH DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000010741759
1.
PERFORM WORK SUPPORT
Perform “INSIDE ANT DIAGNOSIS” on Work Support of “INTELLIGENT KEY”.
Refer to
DLK-75, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (With Super Lock)"
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS RESULT
Perform Self-Diagnosis Result of “BCM”.
Is DTC detected?
YES
>> Refer to
NO
>> GO TO 3.
3.
CHECK PUSH-BUTTON IGNITION SWITCH
Check push-button ignition switch.
Refer to
PCS-110, "Component Function Check"
.
Is the operation normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
REPLACE BCM
BCS-121, "Removal and Installation"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст