Nissan X-Trail 32. Instruction — part 574
AUTOMATIC BACK DOOR WARNING BUZZER
DLK-637
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
AUTOMATIC BACK DOOR WARNING BUZZER
Removal and Installation
INFOID:0000000010717728
REMOVAL
1.
Remove rear bumper fascia. Refer to
EXT-18, "Removal and Installation"
2.
Disconnect automatic back door warning buzzer harness connector.
3.
Remove the automatic back door warning buzzer mounting
nuts
, and then remove automatic back door warning buzzer
.
INSTALLATION
Install in the reverse order of removal.
JMKIB2784ZZ
DLK-638
< REMOVAL AND INSTALLATION >
[TYPE 2]
HANDS FREE SENSOR
HANDS FREE SENSOR
Removal and Installation
INFOID:0000000010717729
REMOVAL
1.
Remove back door inner finisher. Refer to
INT-47, "Removal and Installation"
2.
Disconnect hands free sensor harness connector.
3.
Remove the hands free sensor mounting nuts
, and then
remove hands free sensor
.
INSTALLATION
Install in the reverse order of removal.
JMKIB2843ZZ
APPLICATION NOTICE
DLK-639
< HOW TO USE THIS MANUAL >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOW TO USE THIS MANUAL
APPLICATION NOTICE
Information
INFOID:0000000010713101
Check the vehicle type to use the service information in this section.
Service information
Destination
Handle
Intelligent Key system
Super lock function
Type 1
RHD
With
With
Type 2
LHD
With
Without
Type 3
RHD
Without
With
Type 4
LHD
Without
Without
DLK-640
< PRECAUTION >
[TYPE 3]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010708328
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Instruction.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000010708329
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precautions for Removing Battery Terminal
INFOID:0000000010708330
When disconnecting the battery terminal, pay attention to the following.
• Always use a 12V battery as power source.
• Never disconnect battery terminal while engine is running.
PIIB3706J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст