Nissan X-Trail 32. Instruction — part 312
CO-74
< REMOVAL AND INSTALLATION >
[R9M]
RADIATOR
*Refer to the illustrations for the specific position each hose clamp tab.
• The angle
created by the hose clamp pawl and the specified line
must be within
±
30
°
as shown in the figure.
Radiator hose
Hose end
Paint mark
Position of hose clamp*
: Vehicle upper
Radiator hose (upper)
Radiator side
Upper
Engine side
Upper
Radiator hose (lower)
Radiator side
Upper
Engine side
Front
JPCIA0366ZZ
JPCIA0362ZZ
JPBIA6939ZZ
JPCIA0362ZZ
JPBIA6940ZZ
JPBIA4295ZZ
RADIATOR
CO-75
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
• To install hose clamps
, check that the dimension (A) from the
hose end to the hose clamp is within the reference value.
Inspection
INFOID:0000000010782999
INSPECTION AFTER INSTALLATION
• Check for leakage of engine coolant using the radiator cap tester adapter (commercial service tool) and the
radiator cap tester (commercial service tool). Refer to
• Start and warm up the engine. Visually check that there is no leakage of engine coolant.
Dimension “A”
3 - 5 mm
0.12 - 0.20 in
JPBIA3527ZZ
CO-76
< REMOVAL AND INSTALLATION >
[R9M]
COOLING FAN
COOLING FAN
Exploded View
INFOID:0000000010783000
Removal and Installation
INFOID:0000000010783001
REMOVAL
1.
Remove engine under cover. Refer to
EXT-39, "ENGINE UNDER COVER : Exploded View"
2.
Drain engine coolant from radiator. Refer to
.
CAUTION:
• Perform this step when engine is cold.
• Never spill engine coolant on drive belts.
3.
Remove air duct 1 and air duct 2. Refer to
.
4.
Remove radiator hose (upper) from radiator. Refer to
5.
Remove air inlet tube 2 and air inlet hose 2. Refer to
6.
Remove front grille. Refer to
.
7.
Remove crash zone sensor. Refer to
.
8.
Remove hood lock bell crank and hood lock assembly. Refer to folloing table:
How to select vehicle type: refer to
.
9.
Disconnect harness connectors from cooling fan and fan resistor, and move harness to aside.
Cooling fan assembly
Fan resistor
JPBIA6922ZZ
TYPE
Reference
1
2
3
4
COOLING FAN
CO-77
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
10. Remove mounting bolts
and clips
of mounting bracket
.
11. Remove radiator core support upper. Refer to folloing table:
How to select vehicle type: refer to
.
12. Remove cooling fan assembly according to the following instructions:
a.
Remove screws
.
b.
Unlock pawl
(
1), and side mounting part
(
2).
c.
Remove cooling fan assembly
to upward of vehicle (
3).
CAUTION:
Be careful not to damage or scratch on radiator core when
removing.
13. Remove fan resistor, if necessary.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Only use genuine parts for fan shroud mounting bolt and observe the specified torque (to prevent
radiator from being damaged).
NOTE:
Cooling fans are controlled by ECM. For details. Refer to
EC-843, "COOLING FAN CONTROL : System
.
Inspection
INFOID:0000000010783003
INSPECTION AFTER DISASSEMBLY
JSBIA5285ZZ
TYPE
Reference
1
DLK-268, "R9M : Exploded View"
2
DLK-576, "R9M : Exploded View"
3
DLK-738, "R9M : Exploded View"
4
DLK-880, "R9M : Exploded View"
: Cooling fan assembly
JSBIA5284ZZ
JPBIA6941ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст